Log Loader Pillar - Disassemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 138-7576 | Link Brackets | 2 |
B | 1U-9758 | Stands | 4 |
C | 5P-5197 | Retaining Ring Pliers | 1 |
1U-6728 | Tip Set | 1 |
Start By:
- Remove the log loader pillar. Refer to Operation and Maintenance Manual, "Log Loader Pillar - Remove".
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Install pin (1) in the top of the pillar. Use Tooling (A), a threaded rod, and two nuts in order to attach a hoist and lifting slings to the pillar. Attach lifting chains to the lower portion of the pillar in order to keep the pillar completely vertical.
- Place the pillar in the vertical position on Tooling (B). The weight of the pillar is
250 kg (550 lb) .Show/hide tableIllustration 2 g00627746 - Remove two bushings (3) from the pillar base.
- Remove two O-ring seals (2) from the pillar base.
Show/hide table
Illustration 3 g00627789 - Remove eight bolts (4) and cover plate (5).
Show/hide table
Illustration 4 g00627802 - Remove seal (7).
- Remove plug (9).
- Use Tooling (C) to remove retainer (8). Remove ring (6).
- Use the hoist and the lifting slings in order to separate the pillar from the pillar base.
Show/hide table
Illustration 5 g00628046 - Use a hoist and suitable lifting slings to place the pillar base in the horizontal position.
- Remove two bolts (10) and the washers. Remove service platform (11).
- Repeat Step 11 for service platform (11) on the other side of the pillar, as required.
Show/hide table
Illustration 6 g00628054 - Remove clamp (13) which holds oil tube (15) in place.
- Disconnect oil tube (15).
- Remove eight bolts (14) and the bushings.
- Remove tube (12).
Show/hide table
Illustration 7 g00628090 - Remove O-ring seal (16) from tube (12).
Show/hide table
Illustration 8 g00628093 Show/hide tableIllustration 9 g00628094 - Use two persons to remove bar (17). The weight of bar (17) is approximately
25 kg (55 lb) . - Remove four bolts (25) and four seals (22) from bar (17).
- Remove retainer (21) and ring (20).
- Remove piston (23). Remove seals (18), (19), and (24).
- Repeat Steps 13 through 21 for the other tube assemblies, as required.
Show/hide table
Illustration 10 g00628168 Show/hide tableIllustration 11 g00628169 - Remove bearing (27).
- After two bars (17) are removed, remove bolt (26). Remove bearing (28) from the inside of the pillar base. Remove bolt (26) and bearing (28) from the other side of the pillar base.
- Remove seal (31), bushing (30), and scraper (29) from the pillar base.
Show/hide table
Illustration 1 | g00627916 |
Caterpillar Information System:
CB-534D and CB-564D Asphalt Compactors Throttle Control
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0562 - FMI 09
826G Series II Landfill Compactor, 825G Series II Soil Compactor and 824G Series II Wheel Dozer Engine Supplement Turbocharger - Install - Engine in Chassis
CB-534D and CB-564D Asphalt Compactors Mirror
120H, 12H, 135H, 140H, 143H, 14H, 160H, 163H and 16H Motor Graders Caterpillar Monitoring System Diagnostic Capabilities
533 Wheel Feller Buncher and 543 Wheel Feller Buncher Power Train Stroking Pressure of Piston Motor (Power Train) - Test and Adjust
554 Forwarder and 574 Forwarder Machine Systems Bank Valve (Eight) (Implement) - Assemble
824G Series II Wheel Dozer, 825G Series II Soil Compactor and 826G Series II Landfill Compactor Electrohydraulic System MID 082 - CID 0650 - FMI 12
554 Forwarder and 574 Forwarder Machine Systems Steering Metering Pump - Assemble
AP-1055D and BG-2455D Asphalt Pavers Ventilation Inlet Ducts - Inspect/Clean
AP-655C Asphalt Paver Ventilation Blower Wheel - Inspect/Clean
CB-534D and CB-564D Asphalt Compactors Light Switches
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Safety Messages - Arrangement I
824G Series II Wheel Dozer, 825G Series II Soil Compactor and 826G Series II Landfill Compactor Electrohydraulic System MID 082 - CID 0562 - FMI 12
533 Wheel Feller Buncher and 543 Wheel Feller Buncher Power Train Power Train Troubleshooting
826G Series II Landfill Compactor, 825G Series II Soil Compactor and 824G Series II Wheel Dozer Service Brake Disc Wear Indicator - Check
AP555E and BG555E Asphalt Pavers Wheel Nuts (Final Drive) - Tighten
824G Series II Wheel Dozer, 825G Series II Soil Compactor and 826G Series II Landfill Compactor Electrohydraulic System MID 082 - CID 0497 - FMI 03
2002/03/04 Fabricated Tools Are Required For The Disassembly And Assembly Of The Variable Speed Fan Drive {1359}
533 Wheel Feller Buncher and 543 Wheel Feller Buncher Machine Systems Cylinder Speed - Check
AP-655C and BG-2255C Asphalt Pavers Specifications
AP-655C Asphalt Paver Leaving the Machine
AP-1055D and BG-2455D Asphalt Pavers Push Roller
735 and 740 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Check Valve (Fan Drive Standby Pressure)