Fan Drive Pulley - Remove and Install
Removal Procedure
Start By:
- Prepare the machine for disassembly and assembly procedures. For additional information, refer to Disassembly and Assembly, "Preparation for Disassembly".
- Open the hood. For additional information, refer to Operation and Maintenance Manual, "Tilt Hood".
- Remove bolts (2), the washers, and fan guard (1) .
Show/hide table
Illustration 1 | g00857081 |
- Remove bolts (3), the washers, fan (4), and fan adapter (5) .
Show/hide table
Illustration 2 | g00857059 |
- Release the tension on belt tensioner (7). Remove serpentine belt (8) from fan pulley (6) .
Show/hide table
Illustration 3 | g00857213 |
- Remove bolts (16) and fan pulley (6) .
Show/hide table
Illustration 4 | g00857036 |
- Remove bolts (14), the washers, and bearing bracket (17) .
- Remove grease fitting (15) .
- Remove bolts (19) and plate (18). Remove fan shaft (9) from bearing bracket (17) .
- Remove bolts (10), the washers, and bearing retainer (11) from bearing bracket (17) .
- Remove O-ring seal (12) and roller bearing (13) from bearing bracket (17) .
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 2S-3230     | Bearing Lubricant     | 1     |
- Install roller bearing (13) and O-ring seal (12) in bearing bracket (17) .
Note: Apply a thin layer of Tooling (A) on the outside of roller bearing (13) and O-ring seal (12) .
Show/hide table
Illustration 5 | g00857036 |
- Install grease fitting (15) .
- Install bearing retainer (11), bolts (10), and the washers on bearing bracket (17) .
- Install fan shaft (9) in bearing bracket (17). Install plate (18) and bolts (19) on fan shaft (9).
- Apply approximately 50 grams of Tooling (A) in the cavity between bearing bracket (17) and fan shaft (9). Install bearing bracket (17), bolts (14), and the washers.
- Install fan pulley (6) and bolts (16) .
- Release the tension on belt tensioner (7). Install serpentine belt (8) on fan pulley (6) .
Show/hide table
Illustration 6 | g00857213 |
- Install fan adapter (5), fan (4), bolts (3), and the washers.
Show/hide table
Illustration 7 | g00857059 |
- Install fan guard (1), bolts (2), and the washers.
Show/hide table
Illustration 8 | g00857081 |
- Close the hood. For additional information, refer to Operation and Maintenance Manual, "Tilt Hood".
Caterpillar Information System:
TH103 Telehandler Hydraulic System Access Platform - Test and Adjust
PM-465 Cold Planer Fuel System Secondary Filter - Replace
CB-634D Paving Compactor Cooling System Coolant (ELC) - Change
570B Wheel Harvester and 580B Wheel Harvester Engine Supplement Crankshaft Front Seal - Remove and Install - Engine in Chassis
2001/12/17 Correction to Specifications , "Steering Gear" {4310}
3126B Engine for Caterpillar Built Machines System Overview
533 Wheel Feller Buncher and 543 Wheel Feller Buncher Power Train Drive Shaft (Machine)
TH103 Telehandler Hydraulic System Pressure for Pump and Relief Valve (Main) - Test and Adjust
2001/12/17 A New Retaining Clip will Improve the Alignment of the Hose Assembly on the Condenser {1374, 1808, 5057, 7320}
CB-534D, CB-534D XW and CB-564D Vibratory Compactors Machine Systems Water Spray Pump - Assemble
CB-534D, CB-534D XW and CB-564D Vibratory Compactors Machine Systems Water Spray Pump - Disassemble
533 Wheel Feller Buncher and 543 Wheel Feller Buncher Power Train Transmission Gearbox
533 Wheel Feller Buncher and 543 Wheel Feller Buncher Power Train Bevel Gear and Pinion
PM-465 Cold Planer Fuel Tank Cap and Strainer - Clean
3054 Engine for Caterpillar Built Machines Cylinder Head - Remove
3054 Engine for Caterpillar Built Machines Cylinder Head - Install
3054 Engine for Caterpillar Built Machines Crankshaft - Remove
3054 Engine for Caterpillar Built Machines Crankshaft - Install
TH350B, TH355B, TH360B and TH460B Telehandlers Reference Material
PM-465 Cold Planer Engine Crankcase Breather - Clean
2002/01/28 Serviceable Parts for Brake Master Cylinder Are Now Available {4258}
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Axle (without Brakes) - Disassemble
793C and 793C XQ Off-Highway Trucks Hydraulic System Pad Assembly (Truck Body) - Install and Adjust
CP-433E, CS-433E and CS433E Vibratory Soil Compactors Propel System Hydraulic Oil Filter