Electronic Unit Injector Sleeve - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 4C-5552     | Large Bore Brush     | 1     |
B     | 9U-7237     | Brush Extension     | 1     |
9U-7244 | End Brush     | 1     | |
C     | 9U-7258     | Driver Cap     | 1     |
D     | 221-9778     | Puller Stud     | 1     |
E     | 4C-9507     | Retaining Compound     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tool (A) to clean the unit injector bore.
Show/hide table
Illustration 1 | g00512115 |
- Use Tool (B) to clean the unit injector seat.
Note: Check the fuel passage in the cylinder head assembly. Remove any debris left from the use of Tool (A) and Tool (B) .
- Apply tooling (E) to upper land (1) and lower land (2) on the unit injector sleeve.
- Install Tooling (D) into the threads of unit injector sleeve.
Show/hide table
Illustration 2 | g03321660 |
- Position Tooling (D) and the unit injector sleeve in the cylinder head.
- Use Tooling (C) and a hammer to install unit injector sleeve in the cylinder head.
- Repeat Step 1 through Step 6 in order to install the remaining unit injector sleeves.
End By: Install the electronic unit injectors.
Caterpillar Information System:
966G Series II and 972G Series II Wheel Loaders Engine Supplement Electronic Unit Injector Sleeve - Remove
AP-1050B and BG-245C Asphalt Pavers Ventilation Inlet Ducts - Inspect/Clean
773E Off-Highway Truck/Tractor and 775E Quarry Truck Window Washer Reservoir - Fill
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders Sensors and Electrical Connectors
769D Off-Highway Truck and 771D Quarry Truck Torque Converter and Transmission Oil - Change
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Hydraulic System Pilot Valve (Oil Manifold) - Pilot Hydraulic System
2014/12/11 Hopper Inserts are used with Caterpillar Asphalt Pavers {6639}
2001/10/29 A New Seal Is Now Used In The Track Adjuster Cylinders {4157}
773E Off-Highway Truck Steering System Oil - Change
3126 Truck Engine Flywheel Housing
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Diagnostic Code List
769D Off-Highway Truck and 771D Quarry Truck Oil Filter (Steering Pump Case Drain) - Replace
TH350B, TH355B, TH360B and TH460B Telehandlers Operation
TH350B, TH355B, TH360B and TH460B Telehandlers Plate Locations and Film Locations
TH210 and TH215 Telehandlers Power Train Hydrostatic Drive System
TH210 and TH215 Telehandlers Power Train Piston Motor (Hydrostatic)
TH210 and TH215 Telehandlers Power Train Piston Pump (Hydrostatic)
TH350B, TH355B, TH360B and TH460B Telehandlers Towing the Machine
Installation and Reinforcement Procedures for the Upper Link{7120} Installation and Reinforcement Procedures for the Upper Link{7120}
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Features
3408E and 3412E Engines for Caterpillar Built Machines Cat Data Link Circuit - Test
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System CID 0710 FMI 06 Solenoid Valve (Auto Retarder Supply) Current Above Normal - Test
2003/03/10 Correction to Specifications, Systems Operation, Testing and Adjusting , "Axle Housing and Bearing Preload - Adjust" {3260}
2001/10/29 Correction To Service Manual Module, SENR1126, "Disassembly And Assembly Of 3500B Machine Engines" , "Remove And Install Cylinder Head Assemblies" {1100, 1101}