Electronic Unit Injector Sleeve - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A (1)     | 9U-7259     | Puller Stud     | 1     |
128-7889 | Bridge Puller     | 1     | |
9U-6877 | Thrust Bearing     | 1     | |
5P-8247 | Hard Washer     | 1     | |
4K-0367 | Nut     | 1     |
Show/hide table
( 1 ) | The tools that are listed in the chart are part of the 9U-6891 Injector Tool Group . |
Start By:
- Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install the puller stud from Tooling (A) into the unit injector sleeve.
Show/hide table
Illustration 1 | g00512128 |
- Install the following parts from Tooling (A) over the puller stud: bridge puller, thrust bearing, hard washer and nut.
Show/hide table
Illustration 2 | g00512002 |
- Tighten the nut until the unit injector sleeve is pulled free of the cylinder head assembly.
- Remove Tooling (A) from the unit injector sleeve.
- Repeat Steps 1 through 4 in order to remove the remaining unit injector sleeves.
Caterpillar Information System:
AP-1050B and BG-245C Asphalt Pavers Ventilation Inlet Ducts - Inspect/Clean
773E Off-Highway Truck/Tractor and 775E Quarry Truck Window Washer Reservoir - Fill
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders Sensors and Electrical Connectors
769D Off-Highway Truck and 771D Quarry Truck Torque Converter and Transmission Oil - Change
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Hydraulic System Pilot Valve (Oil Manifold) - Pilot Hydraulic System
2014/12/11 Hopper Inserts are used with Caterpillar Asphalt Pavers {6639}
2001/10/29 A New Seal Is Now Used In The Track Adjuster Cylinders {4157}
773E Off-Highway Truck Steering System Oil - Change
3126 Truck Engine Flywheel Housing
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Diagnostic Code List
769D Off-Highway Truck and 771D Quarry Truck Oil Filter (Steering Pump Case Drain) - Replace
TH210 and TH215 Telehandlers Steering System Steering System Troubleshooting
966G Series II and 972G Series II Wheel Loaders Engine Supplement Electronic Unit Injector Sleeve - Install
TH350B, TH355B, TH360B and TH460B Telehandlers Operation
TH350B, TH355B, TH360B and TH460B Telehandlers Plate Locations and Film Locations
TH210 and TH215 Telehandlers Power Train Hydrostatic Drive System
TH210 and TH215 Telehandlers Power Train Piston Motor (Hydrostatic)
TH210 and TH215 Telehandlers Power Train Piston Pump (Hydrostatic)
TH350B, TH355B, TH360B and TH460B Telehandlers Towing the Machine
Installation and Reinforcement Procedures for the Upper Link{7120} Installation and Reinforcement Procedures for the Upper Link{7120}
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Features
3408E and 3412E Engines for Caterpillar Built Machines Cat Data Link Circuit - Test
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System CID 0710 FMI 06 Solenoid Valve (Auto Retarder Supply) Current Above Normal - Test
2003/03/10 Correction to Specifications, Systems Operation, Testing and Adjusting , "Axle Housing and Bearing Preload - Adjust" {3260}