Pilot Control Actuator (Ejector)
Show/hide table
 | |
| Illustration 1 | g00832238 |
(1) Torque on the bolts ... 3 ± 0.25 N·m (27 ± 2.212 lb in)
The orientation of the solenoid should match the illustration above.
When you replace a bolt, assemble three washers with the new bolt.
(2) 112-5874 Proportional Solenoid
(3) 137-4756 Spring
- Test force ... 23.40 ± 0.71 N (5.261 ± 0.160 lb)
- Length under force ... 8 mm (0.315 inch)
- Free length after test ... 11.60 mm (0.457 inch)
- Outside diameter ... 10.312 mm (0.4060 inch)
- Length under force ... 8 mm (0.315 inch)
(4) 159-8402 Feedback Spring
- Test force ... 21.01 ± 0.63 N (4.723 ± 0.142 lb)
- Length under force ... 46.5 mm (1.83 inch)
- Free length after test ... 54.03 mm (2.127 inch)
- Outside diameter ... 12.4 mm (0.49 inch)
- Length under force ... 46.5 mm (1.83 inch)
The feedback spring is designated with one red stripe.
(5) 141-5498 Spring
- Test force ... 138 ± 11 N (31.0 ± 2.5 lb)
- Length under force ... 43 mm (1.7 inch)
- Free length after test ... 77.5 mm (3.05 inch)
- Outside diameter ... 21 mm (0.8 inch)
- Length under force ... 43 mm (1.7 inch)
(6) 141-5497 Spring
- Test force ... 192.6 ± 15.4 N (43.30 ± 3.46 lb)
- Length under force ... 40 mm (1.6 inch)
- Free length after test ... 64.08 mm (2.523 inch)
- Outside diameter ... 28.6 mm (1.13 inch)
- Length under force ... 40 mm (1.6 inch)
Caterpillar Information System:
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bucket Cylinder (Backhoe)
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bucket Cylinder (Backhoe)
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader CID 0617 FMI 06 Air Inlet Heater Relay grounded/current above norm
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader CID 0617 FMI 05 Air Inlet Heater Relay open/current below normal
CS-531D, CP-533D and CS-533D Vibratory Compactors Hydraulic Tank Vent - Replace
3056 Engines Cylinder Block
740 EJECTOR Articulated Truck Body Mounting - Lubricate
TH350B, TH355B, TH360B and TH460B Telehandlers Stopping the Machine
3176C, 3196 and 3406E Engines for Caterpillar Built Machines E272 Inlet Air Restriction Warning
3176C, 3196 and 3406E Engines for Caterpillar Built Machines Engine Fan Control Solenoid Circuit - Test
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Swing Cylinder
TL5 Series Field Cultivator Model View Illustrations
TH210 and TH215 Telehandlers Steering System General Information
TL5 Series Field Cultivator Specifications
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Stick Cylinder
140H and 160H Motor Graders Engine Supplement Engine Oil Filter Base - Disassemble
140H and 160H Motor Graders Engine Supplement Engine Oil Filter Base - Assemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Flywheel - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Install
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Stick Cylinder
3024C Engine for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System MID 079 - CID 0347 - FMI 03
2002/10/21 A Revised Counterweight Group Is Now in Production {7056}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Stick Cylinder