Vibratory Support - Assemble
组装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 6V-4074     | 活动扳手     | 1     |
C     | 4C-9507     | 挡圈固定胶     | 1     |
- 检查并清理所有零件。 如果任何零件磨损或损坏,则应使用 Caterpillar 新件进行更换。
- 检查所有密封件。 必须更换损坏的密封件。 用新的 Caterpillar 密封件进行更换。
- 将轴承外圈 (10) 安装到壳体 (9) 中。
Show/hide table
图 1 | g00825720 |
- 将轴承内圈 (8) 装入壳体 (9) 。
注: 轴承内圈应清洁且没有任何润滑油。 如果轴承内圈上有油脂,则将会影响滚动扭矩的读数。
- 将唇型密封 (13) 安装在壳体 (9) 中。 唇型密封内的弹簧必须朝向壳体内部安装。
- 将清洁油脂涂抹在密封件罩 (11) 上。 将密封件罩 (11) 安装到壳体 (9) 上。
- 将心轴 (12) 定位到法兰端上。 将壳体 (9) 降低到心轴 (12) 上,直到轴承内圈 (8) 与心轴上的法兰相接触。
- 将轴承内圈 (4) 压入心轴 (12) ,直到获得少量轴承端隙 0.102 ± 0.025 mm (0.0040 ± 0.0010 in)。 测量唇型密封 (13) 、密封罩 (11) 和轴承内圈的滚动扭矩。
- 挤压轴承内圈 (4) ,直到滚动扭矩增加 1.4 ± 0.3 N·m (12.5 ± 2.5 lb in),以高于步骤 8 测量的滚动扭矩值。 如果增加量大于 1.4 ± 0.3 N·m (12.5 ± 2.5 lb in),轻敲心轴 (12) 的端部。
- 安装垫圈 (3) 。
- 将工具 (C) 涂抹到轴承螺母 (2) 的螺纹上。 使用工具 (A) 将轴承螺母 (2) 安装到心轴 (12) 上。
- 转动壳体 (9) 并让轴承落座。 拧紧轴承螺母 (2) 值最大扭矩 373 N·m (275 lb ft)。 该组装应没有端隙。 滚动扭矩必须增加 2.8 ± 1.7 N·m (25 ± 15 lb in),以高于步骤 8 中测量的滚动扭矩值。 该步骤将会产生 0.038 ± 0.013 mm (0.0015 ± 0.0005 in) 的轴承预负载。
- 轻敲心轴 (12) 的端部,再次检查滚动扭矩。
- 比较步骤 12 至 13 的滚动扭矩。 如果滚动扭矩不相等,则必须再次扭转轴承螺母 (2) 。
- 将垫圈 (3) 上的锁片弯向心轴 (12) 。
- 将冲头插入壳体 (9) 中的孔,然后在两个位置定位轴承螺母 (2) 。
- 将 O 形密封圈安装在螺塞 (6) 和螺塞 (7) 上。 将螺塞 (6) 和螺塞 (7) 安装到壳体 (9) 中。
- 将 O 形密封圈 (5) 安装在接头 (1) 上。 将接头 (1) 安装到壳体 (9) 中。
End By: 安装振动支架。 请参阅 拆解和组装, "发动机振动支架 - 安装"。
Caterpillar Information System:
2001/09/17 Correction to Systems Operation , "Monitoring System" {7490}
CP-433E, CS-423E and CS-433E Paving Compactors Sampling Interval and Location of Sampling Valve
CS56B, CP56B, CS66B, CS68B and CP68B Vibratory Soil Compactors Machine Systems Vibratory Support - Disassemble
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks E038 Low Engine Coolant Temperature Warning
2001/11/19 Prerequisites for Flashing Software into Machine Electronic Control Modules {7620}
PM-465 Cold Planer Maintenance Interval Schedule
2001/10/01 New Torque Procedure for the Bushings that Retain the Fuel Injection Pumps (Disassembly and Assembly Manuals) {1251}
797 Off-Highway Truck Steering System Accumulator Charging Valve
2001/10/01 New Torque Procedure for the Bushings that Retain the Fuel Injection Pumps (Testing and Adjusting Manuals) {1251}
CP-433E, CS-433E and CS433E Vibratory Soil Compactors Propel System Axle
TK1051 Track Feller BuncherEngine Supplement Fan - Remove and Install
CP-433E, CS-433E and CS433E Vibratory Soil Compactors Propel System Direction and Speed Control
2002/04/01 Intervals for Service Inspection {5077, 5081}
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Vibratory Support - Install
120H and 135H Motor Graders Machine Systems Blower Motor (Air Conditioner and Heater) - Remove and Install
216, 226 and 228 Skid Steer Loaders Machine Systems Piston Pump
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Event Codes
3126B Engine for Caterpillar Built Machines Throttle Lock Lamp Circuit - Test
3408E Engine Supplement for 769D Off-Highway Trucks and 771D Off-Highway Quarry Trucks Electric Drive Pump (Prelubrication) - Remove
C-9 Engines for Caterpillar Built Machines Alternator and Regulator
CB-534C Vibratory Compactor Sound Information and Vibration Information
CB-534C Vibratory Compactor Specifications
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Piston Motor (Vibratory) - Remove
3408E Engine Supplement for 769D Off-Highway Trucks and 771D Off-Highway Quarry Trucks Unit Injector Hydraulic Pump - Remove