Center Axle - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 8S-9096 | Ratchet Puller | 2 |
B | 1U-8228 | Lifting Sling | 2 |
C | 140-7742 | Protective Sleeve | 2 |
D | 8S-7640 | Stand | 2 |
8S-7621 | Tube | 2 |
- Inspect all parts and clean all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Show/hide table
Illustration 1 g00525083 - Attach Tooling (B) and (C) to dump body (15), as shown.
Show/hide table
Illustration 2 g00525082 - Rotate the wheels in order to install axle housing (2) to the machine. Use the hoist in order to raise the dump body off Tooling (D). Remove Tooling (D) from underneath dump body (15). Continue positioning axle housing (2) to the machine.
- Position an appropriate floor jack under the shaft yoke that is on axle housing (2). Use the floor jack in order to raise the shaft yoke to a level position.
Show/hide table
Illustration 3 g00525083 - Use Tooling (B) and (C) in order to lower dump body (15) on the center axle housing.
Show/hide table
Illustration 4 g00525060 - Install four bolts (11) and the washers that secure bracket (12) to axle housing (2). Tighten bolts (11) to a torque of
270 ± 40 N·m (199 ± 30 lb ft) . - Install four bolts (13) and the washers that secure axle housing (2) to the center suspension frame. Tighten bolts (13) to a torque of
900 ± 100 N·m (664 ± 74 lb ft) .Show/hide tableIllustration 5 g00525059 - Install four bolts (7) and the washers that secure bracket (8) to axle housing (2). Tighten bolts (7) to a torque of
270 ± 40 N·m (199 ± 30 lb ft) . - Position bracket (10) to the axle housing. Install four bolts (9) and the washers that secure bracket (10) and axle housing (2) to the center suspension frame. Tighten bolts (9) to a torque of
900 ± 100 N·m (664 ± 74 lb ft) .Show/hide tableIllustration 6 g00525081 - Remove Tooling (A) from each side of center suspension frame (14).
Show/hide table
Illustration 7 g00525083 - Remove Tooling (B) and (C) from dump body (15).
Show/hide table
Illustration 8 g00525058 - Connect breather hose (3) to center axle housing (2). Connect hydraulic hose (6) to the differential. Install bolt (5), the washer and hose clamp (4) that secures hydraulic hose (6) to the differential.
Show/hide table
Illustration 9 g00525057 - Connect hydraulic brake hose (1) to the brake line that is on center axle housing (2).
- Fill the axle housing with fluid to the proper level. Refer to Operation and Maintenance Manual, "Differential and Final Drive Oil - Change".
End By:
- Install the stabilizer rod for the center axle. Refer to Disassembly and Assembly, RENR3447, "Center Axle Stabilizer Rod - Remove and Install".
- Install the rear axle housing. Refer to Disassembly and Assembly, "Rear Axle Housing - Install".
- Install the center drive shaft. Refer to Disassembly and Assembly, "Center Drive Shaft - Remove and Install".
- Purge the air out of the braking system. Refer to Systems Operation, Testing and Adjusting, RENR3488, "Service Brake Air - Purge".
Caterpillar Information System:
725, 730 and 730 EJECTOR Articulated Trucks Power Train Center Axle - Remove
725, 730 and 730 EJECTOR Articulated Trucks Power Train Rear Axle - Install
725, 730 and 730 EJECTOR Articulated Trucks Power Train Rear Axle - Remove
735 Articulated Truck Backup Alarm
CP-663E, CS-663E and CS-683E Vibratory Compactors Belts - Inspect/Adjust/Replace
432D and 442D Backhoe Loaders All Wheel Steer Control - If Equipped
725, 730 , 730 EJECTOR, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System - AT Directional Shift Management Function
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System Controlled Throttle Shifting Function
AP-1000B and BG-260C Asphalt Pavers Backup Alarm - Test
HF181 Felling Head, HF201 Felling Head and HF221 Felling Head for Track Feller Bunchers Transport Guard - Remove and Install
CP-563D, CS-563D, CS-573D and CS-583D Paving Compactors Lubricant Viscosities
2000/11/13 Special Instruction, REHS0034-04 for Repairing the Nonmetallic Fenders, Machine Hoods and Tank Covers is Now Updated {1273, 7251, 7252}
735 Articulated Truck Hood Control
725 and 730 Articulated Trucks Braking System Pump Flow - Test
561M Pipelayer Boom Winch Motor - Disassemble
561M Pipelayer Boom Winch Motor - Assemble
HP750 Processing Head Reference Material
HP750 Processing Head Capacities (Refill)
561M Pipelayer Boom Winch - Disassemble
561M Pipelayer Boom Winch - Assemble
735 Articulated Truck Battery Disconnect Switch
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Machine Systems Hydraulic Tank - Disassemble
725 and 730 Articulated Trucks Braking System Solenoid Valve (Parking Brake) - Test
3054B Engine for Caterpillar Built Machines Inlet Manifold