Axle Shaft - Remove
Removal Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 2P-8312 | Retaining Ring Pliers | 1 |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Move the machine in order to position drain plug (1) at the bottom of cover (2) . Remove the drain plug in order to allow the oil to drain.
Show/hide table
 | |
| Illustration 1 | g00507932 |
- Remove bolts (3) and the washers. Remove cover (2) and the O-ring seal from final drive (4) .
- Remove axle shaft (5) and sun gear (6) from the axle housing.
Show/hide table
 | |
| Illustration 2 | g00507944 |
- Use Tooling (A) and remove retaining ring (7) from axle shaft (5) . Remove sun gear (6) from the axle shaft.
Show/hide table
 | |
| Illustration 3 | g01308660 |
Caterpillar Information System:
725, 730 and 730 EJECTOR Articulated Trucks Power Train Tire and Rim - Install
725, 730 and 730 EJECTOR Articulated Trucks Power Train Tire and Rim - Remove
2000/12/04 Electronic Control Modules and Computer Viruses {7610}
561M Pipelayer Counterweight Cylinder - Install
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0177 - FMI 03
420D, 430D, 432D and 442D Backhoe Loaders Auxiliary Hydraulic Electronic Control System MID 106 - CID 1189 - FMI 00
446B Backhoe Loader Transmission (Autoshift) Power Train Troubleshooting
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0168 - FMI 01
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader ATA (SAE J1587 / J1708) Data Link Circuit - Test
Assembly Procedures for the 776D Tractors and for the 777D Off-Highway Trucks{7000, 7960} Assembly Procedures for the 776D Tractors and for the 777D Off-Highway Trucks{7000, 7960}
CB22, CB24, CB32 and CC24 Vibratory Compactor Water Separator (Fuel Priming Pump and Primary Fuel Filter) - Assemble
CB22, CB24, CB32 and CC24 Vibratory Compactor Water Separator (Fuel Priming Pump and Primary Fuel Filter) - Disassemble
725, 730 and 730 EJECTOR Articulated Trucks Power Train Axle Shaft - Install
420D, 430D, 432D and 442D Backhoe Loaders Auxiliary Hydraulic Electronic Control System MID 106 - CID 1189 - FMI 01
420D, 430D, 432D and 442D Backhoe Loaders Auxiliary Hydraulic Electronic Control System MID 106 - CID 1189 - FMI 08
420D, 430D, 432D and 442D Backhoe Loaders Auxiliary Hydraulic Electronic Control System Electronic Control Module (ECM) - Replace
432D and 442D Backhoe Loaders Transmission Direction and Speed Control
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Machine Systems Hydraulic Tank - Remove
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0177 - FMI 04
420D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Transmission (Autoshift) Transmission and Torque Converter - Test
424D, 428D and 438D Backhoe Loaders All Wheel Steer Control - If Equipped
420D, 430D, 432D and 442D Backhoe Loaders Auxiliary Hydraulic Electronic Control System Circuit for Enabling Reverse Direction
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Work Tool Coupler Operation
2000/12/04 Tow Point Cylinders May Not Respond On Machines With Topcon Grade Controls {5645, 7219, 7220}