Axle Shaft - Install
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 2P-8312     | Retaining Ring Pliers     | 1     |
- Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
- Position axle shaft (5) into the axle housing.
Show/hide table
Illustration 1 | g01308664 |
- Use a socket and extension in order to seat the axle shaft into the differential.
Show/hide table
Illustration 2 | g00508073 |
- Install sun gear (6) onto axle shaft (5) .
Note: The tire may be turned in order to fit the sun gear onto the axle shaft.
Show/hide table
Illustration 3 | g01308665 |
- Use Tooling (A) and install retaining ring (7) onto axle shaft (5) .
Show/hide table
Illustration 4 | g01308666 |
- Position cover (2) and the O-ring seal onto final drive (4) and install bolts (3) . Install drain plug (1) .
Show/hide table
Illustration 5 | g01308668 |
- Check the oil level of the final drive. Add oil, if necessary. Refer to Operation and Maintenance Manual, "Final Drive Oil Level -Check".
Caterpillar Information System:
725, 730 and 730 EJECTOR Articulated Trucks Power Train Axle Shaft - Remove
725, 730 and 730 EJECTOR Articulated Trucks Power Train Tire and Rim - Install
725, 730 and 730 EJECTOR Articulated Trucks Power Train Tire and Rim - Remove
2000/12/04 Electronic Control Modules and Computer Viruses {7610}
561M Pipelayer Counterweight Cylinder - Install
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0177 - FMI 03
420D, 430D, 432D and 442D Backhoe Loaders Auxiliary Hydraulic Electronic Control System MID 106 - CID 1189 - FMI 00
446B Backhoe Loader Transmission (Autoshift) Power Train Troubleshooting
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0168 - FMI 01
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader ATA (SAE J1587 / J1708) Data Link Circuit - Test
Assembly Procedures for the 776D Tractors and for the 777D Off-Highway Trucks{7000, 7960} Assembly Procedures for the 776D Tractors and for the 777D Off-Highway Trucks{7000, 7960}
CB22, CB24, CB32 and CC24 Vibratory Compactor Water Separator (Fuel Priming Pump and Primary Fuel Filter) - Assemble
420D, 430D, 432D and 442D Backhoe Loaders Auxiliary Hydraulic Electronic Control System MID 106 - CID 1189 - FMI 01
420D, 430D, 432D and 442D Backhoe Loaders Auxiliary Hydraulic Electronic Control System MID 106 - CID 1189 - FMI 08
420D, 430D, 432D and 442D Backhoe Loaders Auxiliary Hydraulic Electronic Control System Electronic Control Module (ECM) - Replace
432D and 442D Backhoe Loaders Transmission Direction and Speed Control
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Machine Systems Hydraulic Tank - Remove
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System MID 027 - CID 0177 - FMI 04
420D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Transmission (Autoshift) Transmission and Torque Converter - Test
424D, 428D and 438D Backhoe Loaders All Wheel Steer Control - If Equipped
420D, 430D, 432D and 442D Backhoe Loaders Auxiliary Hydraulic Electronic Control System Circuit for Enabling Reverse Direction
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Work Tool Coupler Operation
2000/12/04 Tow Point Cylinders May Not Respond On Machines With Topcon Grade Controls {5645, 7219, 7220}
725, 730, 735, 740 and 740 EJECTOR Articulated Trucks Power Train Electronic Control System General Information