Rear Suspension (Cylinder) - Remove
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 7S-5106 | 充氮卡盘 | 2 |
B | 4C-5809 | 液压泵 | 1 |
B | 4C-5749 | 推车 | 1 |
C | 9U-7536 | 起吊台架(55 吨) | 2 |
D | 8S-7611 | 管 | 1 |
D | 8S-7615 | 销 | 1 |
D | 8S-7630 | 台架 | 1 |
D | 8S-8048 | 鞍座 | 1 |
Show/hide table
悬架油缸突然移动可造成人员伤亡。 突然上下移动可导致您头部上方的间隙快速变化。 维修前,务必阅读悬架油缸上的所有警告标签。 在氮气压力完全消失前,不要检查悬架油缸内的油。 除非连杆完全收回且氮气压力完全释放,否则任何情况下都不要拆下油缸上的阀门、盖或螺塞。 测试或调整悬架油缸时,不要站在机器下面。 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
- 拆下固定导线线束 (2) 的螺栓 (1) 和夹子。 将线束 (2) 从电气接头上断开。
- 拆下四条螺栓 (4) 和硬垫圈。 拆下板 (3)。
Show/hide table
图 2 g00649255 - 拆下四个螺栓 (5) 和硬垫圈。 使板 (6) 滑下后悬挂油缸。
Show/hide table
图 3 g00649257 注: 为了拆下一个后悬挂油缸,两个后悬挂油缸中的氮气均必须排除。
- 拆下盖(未显示)并将工具 (A) 安装到两个后悬挂油缸的阀上。 排除后悬挂油缸中的氮气。 请参阅悬挂油缸,系统操作、测试和调整, "悬挂油缸(后)- 排气和充气",了解正确的步骤。
Show/hide table
图 4 g00702506 - 将工具 (C) 放置在机器后部下方,如图所示。 将工具 (B) 固定到工具 (C) 上。 使用工具 (B) 和工具 (C) 提升机架组件,直到机器重量离开从后悬挂油缸。
Show/hide table
图 5 g00702556 - 拆下两个内六角头螺栓 (7),然后从后悬挂油缸上拆下有效载荷压力传感器 (8)。
Show/hide table
图 6 g00649392 - 拆下四个内六角头螺栓 (10),然后从后悬挂油缸上拆下歧管 (9)。
Show/hide table
图 7 g00649262 - 拆下固定上销钉 (12)(未显示)的螺栓 (11)、全螺纹螺母和三个垫圈。
Show/hide table
图 8 g00649266 - 安装车斗固定销 (13),在拆下上销钉 (12) 时将后悬挂油缸 (14) 固定到位。 拆下上销钉 (12)。
- 将适当的吊索绕后悬挂油缸 (14) 的连杆端安置。 将吊索固定到适当的举倾机构上。 拆下车斗固定销 (13).
Show/hide table
图 9 g00649270 - 将后悬挂油缸 (14) 的连杆端降低到工具 (D) 上,如图所示。 拆下固定下销钉 (16)(未显示)的螺栓 (15)、全螺纹螺母和三个垫圈。
Show/hide table
图 10 g00649271 - 将适当的吊索绕后悬挂油缸 (14) 的缸盖端安置。 将吊索固定到适当的举倾机构上。 拆下下销钉 (16)。
- 从机器上拆下后悬挂油缸 (14). 后悬挂油缸的重量为
290 kg (640 lb) 。
Show/hide table
图 1 | g00649232 |
Caterpillar Information System:
988G Wheel Loader Electrohydraulic System MID 082 - CID 0357 - FMI 13
2013/08/20 New Optional Service Replacement Wheel Studs are Now Available {4201}
D400E Series II Ejector Truck Changing Speed and Direction
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air Tank (Secondary and Parking Brake) - Remove and Install
2000/06/05 An Improved Breather Cap is Used on the Lubrication Tank {1392}
988G Wheel Loader Electrohydraulic System MID 082 - CID 0356 - FMI 13
2000/05/01 Correction to Operation and Maintenance Manual, SEBU6950 , "Engine Valve Clearance Setting - Adjust" and Operation and Maintenance Manual, SEBU7034 , "Engine Valve Clearance Setting - Adjust" {1102, 1209}
988G Wheel Loader Electrohydraulic System MID 082 - CID 0355 - FMI 13
2001/05/07 Various Hydraulic Connectors are Available for Machines and Work Tools {6129, 6700}
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service Brake (Front Oil Cooled) - Assemble
776D and 777D Off-Highway Truck/Tractors Power Train Power Train Electronic Control Module (Transmission/Chassis)
776D and 777D Off-Highway Truck/Tractors Power Train Power Train Electronic Control Module (Transmission/Chassis)
776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Tire and Rim (Rear) - Remove
10-20B Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed General Information
120H and 135H Motor Graders Cooling System Coolant (ELC) - Change
AP-1000B and BG-260C Asphalt Pavers Propel System Propel System Troubleshooting
TK711, TK721, TK722 and TK732 Track Feller Bunchers Crushing Prevention and Cutting Prevention
140H and 160H Motor Graders Cooling System Coolant (ELC) - Change
D7R Series II Track-Type Tractor Ether Starting Aid Cylinder - Replace - If Equipped
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>129-1502</B> Generator through <B>129-5034</B> Generator
12H Motor Grader Cooling System Coolant (ELC) - Change
824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Braking System General Information (Braking)
3114, 3116, and 3126 Engines Gear Group (Front) - Time
776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Tire and Rim (Rear) - Install