Differential and Bevel Gear - Remove
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 138-7574 | Link Bracket | 2 |
Start By:
- Remove service brakes. Refer to Disassembly and Assembly, "Service Brake - Remove and Install".
- Remove the differential pinion. Refer to Disassembly and Assembly, "Differential Pinion - Remove".
- Install a suitable lifting device, as shown.
- Remove bolts (1) from intermediate housing (2).
- Remove intermediate housing (2) from axle center housing (3). The weight of the intermediate housing is approximately
66 kg (145 lb) .Show/hide tableIllustration 2 g00976104 - Remove thrust bearing (4).
- Install Tooling (A) and a suitable lifting device to differential and bevel gear (5).
- Remove differential and bevel gear (5) from axle center housing (3). The weight of the differential and bevel gear is approximately
136 kg (300 lb) .
Show/hide table
Illustration 1 | g00976103 |
Caterpillar Information System:
3114, 3116, and 3126 Engines Air Inlet and Exhaust System
525B and 535B Wheel Skidders Power Train Service Brake - Remove and Install
525C, 535C and 545C Wheel Skidders Power Train Axle Housing - Assemble
525B and 535B Wheel Skidders Power Train Axle Housing - Disassemble
2000/04/03 Special Instruction, REHS0578, "Assembly Procedure for Large Off-Highway Truck Flat Floor Body Assembly" is Available {7258}
TH62, TH63, TH82, TH83 and TH103 Telehandlers Longitudinal Stability Indicator System Switch (Boom)
988G Wheel Loader Power Train System Schematic
CB-534C and CB-634C Vibratory Compactors Propel System Piston Pump Servo Neutral - Adjust
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Glow Plugs - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Suspension Cylinder Sensor - Troubleshoot
CS-431C, CP-433C and CS-433C Vibratory Compactors Propel System Piston Pump (Axle Propel)
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Air Tank (Service Brake and Retarder) - Remove and Install
525B and 535B Wheel Skidders Power Train Differential and Bevel Gear - Disassemble
525B and 535B Wheel Skidders Power Train Differential Pinion - Disassemble
525B and 535B Wheel Skidders Power Train Differential Pinion - Assemble
525B and 535B Wheel Skidders Power Train Differential and Bevel Gear - Install
AP-1000B and BG-260C Asphalt Pavers Propel System Wheel Alignment - Check and Adjust
3046 Engine for Caterpillar Built Machines Engine Oil Pressure Switch - Test
776D, 777D and 777D HAA Off-Highway Truck/Tractor Power Train Bypass Switch (Transmission Charging Oil Filter)
CB-534C and CB-634C Vibratory Compactors Propel System Piston Pump Case Drain Flow - Test
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Brake Tank (Makeup) - Remove and Install
525B and 535B Wheel Skidders Power Train Differential and Bevel Gear - Assemble
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Warning "Engine Oil Level Is Low" Is Displayed - Troubleshoot
120H Motor Grader V-Belts - Inspect/Adjust/Replace