Engine Speed Control
Show/hide table
 | |
| 图 1 | g00778226 |
312C 的调速器执行器 (1) 调速器执行器 (2) 调速器钢丝绳 (3) 控制接头 | |
Show/hide table
 | |
| 图 2 | g00778227 |
318C 的调速器执行器 (1) 调速器执行器 (2) 调速器钢丝绳 (3) 控制接头 | |
Show/hide table
 | |
| 图 3 | g00686192 |
319C、 320C 和 322C 的调速器执行器 (1) 调速器执行器 (2) 调速器钢丝绳 | |
Show/hide table
 | |
| 图 4 | g00986349 |
321C 的调速器执行器 (1) 调速器执行器 (2) 调速器钢丝绳 | |
Show/hide table
 | |
| 图 5 | g00990169 |
(4) 电子发动机控制装置 | |
控制器将来自发动机转速旋钮 (5) 的信号转化为脉冲宽度调制信号。 随后，控制器将向调速器执行器 (1) 发送信号。 调速器执行器将调整发动机转速旋钮开关 10 个位置的发动机转速。 调速器执行器将利用两根钢丝绳 (2) 控制发动机转速。 一根钢丝绳用来提高发动机转速。 另一根钢丝绳用来降低发动机转速。
注: 325C 系列机型的 HEUI 系统采用 ADEM III 控制器。
Show/hide table
 | |
| 图 6 | g00990178 |
300C 系列机型的发动机转速旋钮开关 (5) 发动机转速旋钮开关 | |
Show/hide table
 | |
| 图 7 | g01057313 |
M325C MH 的发动机转速旋钮开关 (6) 发动机转速旋钮开关 | |
发动机转速旋钮 (5) 分为 10 个位置。 根据发动机转速旋钮的位置确定调速器杆的位置。 旋钮位置显示在监视器面板的字符显示屏上。 空载时每个旋钮位置对应的发动机转速如下表所示。
Show/hide table
| 发动机转速旋钮开关对应的转速 | |||||||
| "位置" | 312C | 315C | 318C / 319C / 320C T1 | 319C / 320C T2 | 321C | 322C T1 / 322C T2 | 325C / 330C |
| 1 | 800 | 930 | 1000 / 900 |
1000 | 800 | 800 | 950 / 800 |
| 2 | 1100 | 1100 | 1100 / 1020 |
1100 | 1020 | 1020 | 1020 |
| 3 | 1250 | 1300 | 1160 | 1200 | 1160 | 1160 | 1160 |
| 4 | 1400 | 1500 | 1300 | 1300 | 1300 | 1300 | 1300 |
| 5 | 1550 | 1650 | 1470 | 1470 | 1470 | 1470 | 1470 |
| 6 | 1700 | 1800 | 1590 | 1590 | 1590 | 1590 | 1590 |
| 7 | 1850 | 1950 | 1700 | 1700 | 1700 | 1700 | 1700 |
| 8 | 1950 | 2100 | 1800 | 1800 | 1800 | 1800 | 1800 |
| 9 | 2050 | 2250 | 1900 | 1900 | 1900 | 1900 | 1900 |
| 10 | 2150 | 2380 | 1970 | 1970 | 1980 | 1970 / 1980 |
1980 |
Caterpillar Information System:
TH103 Telehandler Hydraulic System Auxiliary System
446B Backhoe LoaderSupplement Stopping the Machine
2001/12/24 A Special Instruction, REHS0795 , "Installation of Wiring and Control for the Operation of Work Tools" Is Available {1408}
3034 Engine for Caterpillar Built Machines Rocker Shaft
988G Wheel Loader Braking System Accumulator Charging Valve (Brake)
TH103 Telehandler Hydraulic System Frame Leveling System
3412E Engine for Caterpillar Built Machines CID 0295 FMI 09 Unable to Communicate with LHEX ECM
554 and 574 Forwarders Power Train Hydrostatic Drive System Performance - Test
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Pump Regulation
TH103 Telehandler Hydraulic System Compensating System
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Screed Plates
AP-1000B and BG-260C Asphalt Pavers Auxiliary System Metering Pump (Steering)
TH62, TH63, TH82 and TH83 Telehandlers Boom Retracting and Boom Lowering with Electric Power - Check - If Equipped
446B Backhoe LoaderSupplement Towing the Machine
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Automatic Engine Control
TH103 Telehandler Hydraulic System Stabilizer System
120H Motor Grader Engine Air Precleaner - Clean
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Extension Installation
140H and 160H Motor Graders Engine Air Precleaner - Clean
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 One Touch Low Idle
140H and 160H Motor Graders Engine Crankcase Breather - Clean
321B LCR Excavator Cooling System Coolant Extender (ELC) - Add
120H Motor Grader Engine Crankcase Breather - Clean
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Tool Control