69D and 769D Off-Highway Truck and 771D Quarry Truck Hydraulic System Caterpillar


Relief Valve (Hoist Dual Stage) - Test and Adjust

Usage:

769D 5SS

Table 1
Tools Needed     Qty    
6V-3079 Pressure Hose Assembly     1    
6V-4143 Coupler Assembly     2    
8T-0856 Pressure Gauge (
6000 kPa (870 psi))    
1    
8T-0860 Pressure Gauge (
40000 kPa (5800 psi))    
1    

Note: Make sure that the filters and the screens are clean before you test any pressures. Make sure that the oil is at operating temperature before you perform this test.

Note: Before you perform any tests, visually inspect the entire hydraulic system for oil leaks and for damaged components.

------ WARNING! ------

Personal injury or death can result from sudden machine movement.

Sudden movement of the machine or release of air pressure or oil pressure can cause injury to persons on or near the machine.

To help prevent possible injury before testing and adjusting any air system or hydraulic system, perform the procedure in the Testing and Adjusting, "General Information" section.

----------------------


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.

Dispose of all fluids according to local regulations and mandates.





Illustration 1g00531329

(1) High pressure relief valve

(2) Low pressure relief valve

(3) Hoist dual stage relief valve

(4) Hoist control valve

Hoist dual stage relief valve (3) is part of the hoist control valve (4). The relief pressure for the RAISE position is controlled by high pressure relief valve (1). The relief pressure for the LOWER position is controlled by low pressure relief valve (2) .

Relief Valve Test (High Pressure)




Illustration 2g00531857

(5) Pressure tap

  1. Lower the dump body. Stop the engine.

  1. Connect a hose assembly with an 8T-0860 Pressure Gauge (0 to 40000 kPa (0 to 5800 psi)) to pressure taps (5) .

  1. Start the engine. Operate the dump body repeatedly until the temperature of the hydraulic oil is above 38°C (100°F).

  1. Run the engine at high idle and move the hoist control to the RAISE position.

  1. After the dump body is fully raised, look at the gauge and hold the hoist control in the RAISE position. The high pressure gauge reading is the relief valve pressure setting of high pressure relief valve (1). The correct pressure setting is 17230 ± 520 kPa (2500 ± 75 psi).



    Illustration 3g00531382

    (1) High pressure relief valve

    (2) Low pressure relief valve

    (3) Hoist dual stage relief valve

    (6) Nut

    (7) Retainer

  1. Loosen nut (6). Turn retainer (7) in order to adjust the setting of high pressure relief valve (1) .

  1. When high pressure relief valve (1) is correctly set, tighten nut (6) .

Relief Valve Test (Low Pressure)




Illustration 4g00531859

(8) Pressure tap

  1. Lower the dump body. Stop the engine.

  1. Connect a hose assembly with an 8T-0856 Pressure Gauge (0 to 6000 kPa (0 to 870 psi)) to pressure tap (8) .

  1. Start the engine. Operate the dump body repeatedly until the temperature of the hydraulic oil is above 38°C (100°F).

  1. Lower the dump body onto the truck frame.

    Note: The hoist control must be in the RAISE position before low pressure relief valve (2) can be measured. If the hoist control is in the LOWER position the Power Train Electronic Control Module will keep the hoist control valve in the SNUB position. Low pressure relief valve (2) can not be measured in this condition.

  1. Move a magnet in front of the hoist control until the alert indicator on the dash turns on.

  1. Run the engine at high idle and move the hoist control to the LOWER position.

  1. Look at the gauge and hold the hoist control in the LOWER position. The high pressure gauge reading is the relief valve pressure setting. The correct pressure setting is 3450 ± 350 kPa (500 ± 50 psi).



    Illustration 5g00531539

    (1) High pressure relief valve

    (2) Low pressure relief valve

    (3) Hoist dual stage relief valve

    (9) Retainer

    (10) Nut

  1. Loosen nut (10). Turn retainer (9) in order to adjust the setting of low pressure relief valve (2) .

  1. When low pressure relief valve (2) is correctly set, tighten nut (10) .

Caterpillar Information System:

793C and 793C XQ Off-Highway Truck Air System and Brakes Operational Checks
550 Wheel Harvester, 570 Wheel Harvester and 580 Wheel Harvester Power Train Machine Preparation for Troubleshooting
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Operation
69D and 769D Off-Highway Truck and 771D Quarry Truck Air System and Brakes Brake Valve (Parking and Secondary)
69D and 769D Off-Highway Truck and 771D Quarry Truck Air System and Brakes Air Control Valve (Parking Brake)
769D Off-Highway Truck And 771D Quarry Truck Assembly Procedure{7000, 7006, 7960} 769D Off-Highway Truck And 771D Quarry Truck Assembly Procedure{7000, 7006, 7960}
69D and 769D Off-Highway Truck and 771D Quarry Truck Air System and Brakes Inverter Valve (Secondary Brake)
784C and 785C Off-Highway Trucks Machine Systems Pump Drive - Assemble
69D, 769D, 773D, 773E, 776D and 777D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Power Train Electronic Control System Economy Shift Function
69D and 769D Off-Highway Truck and 771D Quarry Truck Hydraulic System Gear Pump (Hoist and Brake) Efficiency - Test
69D and 769D Off-Highway Truck and 771D Quarry Truck Air System and Brakes Pressure Protection Valve (Brake Air System)
583R Pipelayer Hydraulic System Boom and Hook Control Valve
554 Forwarder and 574 Forwarder Oil Filter (Power Train Charging System) - Replace
550 Wheel Harvester, 570 Wheel Harvester and 580 Wheel Harvester Power Train Visual Inspection
69D and 769D Off-Highway Truck and 771D Quarry Truck Air System and Brakes Air Control Valve (Front Brake)
784C and 785C Off-Highway Truck Power Train Transmission Planetary - Assemble
554 and 574 Forwarders Power Train Power Train Troubleshooting
824G Wheel Tractor, 825G Soil Compactor and 826G Landfill Compactor Hydraulic System Pilot Hydraulic System
69D and 769D Off-Highway Truck and 771D Quarry Truck Air System and Brakes Inverter Valve (Front Brake)
583R Pipelayer Hydraulic System Main Relief Valve
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Body and Canopy - Remove
583R Pipelayer Hydraulic System Counterweight Control Valve
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders and 247, 257, 267, 277 and 287 Multi Terrain Loaders Interlock Electronic Control System Normal Operation
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0147 FMI 03 Pressure Sensor (Lockup Clutch) Voltage Above Normal - Test
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.