Transmission and Torque Converter Pump
Show/hide table
| |
| 图 1 | g02849257 |
Show/hide table
| 区段 | 功能 | 旋向 | 输出（分钟） | RPM | 压力 |
|---|---|---|---|---|---|
| A | 变速箱和变矩器扫油段 | 逆时针 | |
900 | |
| B | 转向离合器和制动器润滑段 | 逆时针 | |
1800 | |
| C | 变速箱充油段 | 逆时针 | |
1800 | |
Show/hide table
| 6T-6090 齿轮泵总成的技术规范 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 泵在组装到箱体和机架前后必须能自由转动。 | |||
| - | 2 | 109-3001 锥形锁紧螺柱 | 用于将泵安装到箱体和机架的两颗锥形锁紧螺柱的扭矩为 |
| 1 | 4 | 6l-4783 螺栓 | 拧紧至扭矩为 |
| 2 | 1 | 5H-4279 杯塞 | 将高强度/高温厌氧法兰密封胶涂覆到塞孔中。 |
| 3 | 1 | 2H-3843 唇形密封 | 利用所密封的润滑剂轻轻润滑密封唇。
将高强度/高温厌氧法兰密封胶涂覆到密封上。 |
| D | - | - | 杯塞的安装深度为 |
Show/hide table
| |
| 图 2 | g02798001 |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
| E | - | - | 新泵中段 "C" 中的齿轮和盖之间的间隙为 |
| F | - | - | 新泵中段 "B" 中的齿轮和泵体之间的间隙为 |
| G | - | - | 新泵中段 "A" 中的齿轮和盖之间的间隙为 |
| H | - | - | 新轴的直径为 |
| J | - | - | 新轴承孔径为 |
Show/hide table
| |
| 图 3 | g02801976 |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
| L | - | - | 两个衬套的接头离垂直中心线的方位为 30 ± 15 度。 |
| 5 | 2 | 9M-4372 衬套 | 安装后衬套的孔径为 |
| M | 安装深度为 |
||
| N | 2 | 8M-8489 定位销 | 定位销伸出机油泵体组件 (4) 端面 |
Show/hide table
| |
| 图 4 | g02801977 |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
| R | - | - | 两个衬套的接头离垂直中心线的方位为 30 ± 15 度。 |
| 6 | 2 | 5M-1995 衬套 | 安装后衬套的孔径为 |
| S | 安装深度为 |
Show/hide table
| |
| 图 5 | g02801978 |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
| U | 4 | 8M-8489 定位销 | 定位销伸出机油泵体 (7) 端面 |
Show/hide table
| |
| 图 6 | g02801979 |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
| W | - | - | 两个衬套的接头离垂直中心线的方位为 30 ± 15 度。 |
| 8 | 2 | 5M-1995 衬套 | 安装后衬套的孔径为 |
| X | 安装深度为 |
Caterpillar Information System:
D250E Series II and D300E Series II Articulated Trucks Power Train Axle Shaft - Remove
583R Pipelayer Power Train Relief Valve (Torque Converter Outlet)
3176C and 3196 Engines for Caterpillar Built Machines General Information
584 and 584HD Forwarders Engine Starting
784C and 785C Off-Highway Trucks Machine Systems Screen (Hoist) - Remove and Install
3406C Engines for Caterpillar Built Machines Engine Oil Filter Base
583R Pipelayer Power Train Torque Divider
980G Wheel Loader Machine Systems Vane Pump (Implement) - Assemble
784C and 785C Off-Highway Trucks Machine Systems Manifold (Hoist) - Remove
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Rear Suspension (Cylinder) - Assemble
793C Off-Highway Truck Power Train Relief Valve (Torque Converter Inlet) - Remove and Install
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Metering Pump (Steering) - Disassemble
769D Off-Highway Truck/Tractor and 771D Quarry Truck Power Train Pressure Control Valve (Transmission)
583R Pipelayer Power Train Transmission Oil Filter
583R Pipelayer Power Train Priority Valve
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Front Suspension (Cylinder) - Disassemble
784C and 785C Off-Highway Trucks Machine Systems Solenoid Valve (Air Start) - Remove and Install
784C and 785C Off-Highway Truck/Tractors Steering System Solenoid and Relief Valve (Steering)
D250E Series II and D300E Series II Articulated Trucks Power Train Axle Shaft - Install
3406C Engines for Caterpillar Built Machines Engine Oil Pump
784C and 785C Off-Highway Truck/Tractors Steering System Metering Pump (Steering)
980G Wheel Loader Machine Systems Piston Pump (Steering) - Disassemble
793C Off-Highway Truck Power Train Relief Valve (Torque Converter Outlet) - Remove and Install
554 Forwarder and 574 Forwarder Model View Illustrations