Water Pump - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
C     | 1P-0510     | 起子总成     | 1     |
D     | 138-9299     | 密封工具     | 1     |
E     | 139-0088     | 密封工具     | 1     |
F     | 4C-9500     | 快速硫化底漆     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (F) 清洁轴 (10) 和壳体 (4) 中油封 (5) 的沉头孔。
Show/hide table
图 1 | g01163722 |
- 使用工具 (C) 将新油封 (5) 安装到壳体 (4) 中。 安装密封时使密封金属表面上的零件号朝向壳体。 确保油封与壳体沉头孔的前边缘平齐。 请勿润滑油封。
- 将轴承内圈 (6) 安装到轴 (10) 上。
- 安置轴承挡圈 (8) ,"此侧朝外"标记朝向轴 (10) 的齿轮端。 安装齿轮 (15) 。 将垫圈 (12) 和螺栓 (13) 安装到轴 (10) 上。 将螺栓 (13) 拧紧到 215 ± 40 N·m (159 ± 30 lb ft) 的扭矩。
- 在轴 (10) 上滑动工具 (D) 。 锥边缘将朝向外侧。
- 将齿轮和轴组件安装到壳体 (4) 中。 小心不要损坏油封。 安装将轴承挡圈 (8) 固定在壳体上的螺栓 (14) 。
- 从轴 (10) 上拆下工具 (D) 。
- 使用工具 (E) 和适合的压力机,将新的密封件 (2) 安装到轴 (10) 上和壳体 (4) 中。 确保密封外侧壳体完全座入壳体中。
- 将叶轮 (3) 定位到轴 (10) 上。 安装垫圈 (9) 和螺栓 (11) 。 拧紧螺栓至扭矩为 39 ± 3 N·m (29 ± 2 lb ft)。
- 将新的 O 形密封圈安装到适配器 (1) 的外侧。 利用干净的机油轻轻润滑密封。
- 将新的 O 形密封圈 (7) 安装到适配器 (1) 上。
- 将适配器 (1) 安置到壳体 (4) 上。
- 将新的 O 形密封圈 (16) 安装到壳体 (4) 中。
End By: 安装水泵。 请参阅 拆解和组装, "水泵 - 安装"。
Caterpillar Information System:
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train System Pressure - Release
3406E On-Highway Engine Water Pump - Disassemble
3406E On-Highway Engine Water Pump - Install
769D Off-Highway Truck and 771D Quarry Truck Lifting and Tying Down the Machine - 769D Off-Highway Truck
784C, 785C and 785C HAA Off-Highway Truck/Tractors Power Train Rear Axle and Final Drive System
773D Off-Highway Truck and 775D Quarry Truck Towing With Inoperable Engine
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Engine Supplement Hydraulic Oil Cooler - Remove and Install
784C, 785C and 785C HAA Off-Highway Truck/Tractors Power Train Transmission Hydraulic System
769D Off-Highway Truck and 771D Quarry Truck Lowering the Body with Engine Stopped
784C and 785C Off-Highway Trucks Machine Systems Check Valve (Rear Air/Hydraulic Cylinder) - Remove and Install
784C, 785C and 785C HAA Off-Highway Truck/Tractors Power Train Power Train Electrical System
Lexion 450, Lexion 460, Lexion 465 andLexion 470 Combines Engine Supplement Water Temperature Sensor - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Slack Adjuster (Rear) - Remove
784C and 785C Off-Highway Truck/Tractors Power Train System Information (Power Train)
784C and 785C Off-Highway Truck/Tractors Power Train Transmission Hydraulic System
784C and 785C Off-Highway Truck/Tractors Power Train Rear Axle and Final Drive System
583R Pipelayer Machine Systems Winch Control Metering Pump - Remove
583R Pipelayer Machine Systems Winch Control Metering Pump - Install
784C, 785C and 785C HAA Off-Highway Truck/Tractors Hydraulic System Relief Valve (Pulled Unit Dual Stage)
583R Pipelayer Machine Systems Winch Control Metering Pump - Disassemble
784C, 785C and 785C HAA Off-Highway Truck/Tractors Hydraulic System Proportioning Solenoid (Pulled Unit)
784C, 785C and 785C HAA Off-Highway Truck/Tractors Hydraulic System Proportioning Solenoid (Hoist)
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Priority Valve - Disassemble
583R Pipelayer Machine Systems Winch Control Metering Pump - Assemble