Drive and Steering Axle (Rear) - Adjust
Adjustment Procedure For The Toe-In
- Raise the rear wheels slightly off the ground.
Show/hide table
Illustration 1 | g00347617 |
The Rear Drive and Steering Axle (1) Nut. (2) Cotter. (3) Tie rod locknut. (4) Adjustment rod. (5) Tie rod joint. (6) Cylinder rod. (A) Distance from the cylinder rod end to the face of the cylinder head. (B) Distance behind the axle from the axle centerline to the hub face. (C) Distance in front of the axle from the axle centerline to the hub face. |
- Install sufficient blocking under the frame and lower the machine to the blocking.
- Tighten the tie rod joint (5) to 300 N·m (221 lb ft).
- Remove the cotter (2) .
- Tighten the nut (1) to 150 N·m (111 lb ft). Tighten the nut (1) to the nearest locking hole.
- Install the cotter (2) .
- Position the cylinder rod (6) until dimension (A) is equal on both sides.
- Loosen the tie rod locknut (3) .
- Adjust the adjustment rod (4) until dimension (B) is equal to dimension (C). The tolerance for dimension (B) and dimension (C) is 0 mm (0.0 inch).
- Tighten the tie rod locknut (3) to 83 N·m (61 lb ft).
- Perform steps 3 through 10 for the opposite side.
- Remove the blocking and lower the machine to the ground.
Adjustment Procedure for the Position Sensor
Show/hide table
REQUIRED TOOLS     | |
Part Number     | Description     |
6V-7070     | Digital Multimeter     |
- Raise the rear wheels slightly off the ground.
Show/hide table
Illustration 2 | g00348393 |
The Rear Drive and Steering Axle (1) Cover. (2) Wire connector. (3) Bolts. |
- Install sufficient blocking under the frame and lower the machine to the blocking.
- Remove three bolts (3) .
- Remove the cover (1) .
- Remove the cable strap that holds wire connector (2) to the axle.
- Disconnect the wire connector (2) .
- Position the cylinder rod (4) until dimension (A) is equal on both sides.
Show/hide table
Illustration 3 | g00348595 |
The Rear Drive and Steering Axle (4) Cylinder rod. (A) Distance from the cylinder rod end to the face of the cylinder head. |
- Connect the Digital Multimeter to the wire terminals (6). Refer to Special Instruction, SEHS7734 for instruction on the multimeter.
Show/hide table
Illustration 4 | g00348571 |
The Rear Drive and Steering Axle (5) Tie rod. (6) Wire terminals. (7) Clamp. (8) Bolt. |
- Loosen the bolt (8) .
- Position the clamp (7) on the tie rod (5) until the resistance is 45.8 ± 1.0 ohms.
- Tighten the bolt (8) .
- Remove the multimeter from the wire terminals (6) .
- Connect the wire connector (2) .
- Install a new cable strap around wire connector (2) and the axle.
- Install the cover (1) and the three bolts (3). Tighten the bolts.
- Remove the blocking and lower the machine to the ground.
Caterpillar Information System:
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Troubleshooting - Transmission
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Troubleshooting - Three-Point Hitch
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Troubleshooting - Steering
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Troubleshooting - Implement Hydraulic System
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Drawbar Adjustment
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Drawbar Pin
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Ground Speed Signal Connector
539 Knuckleboom Loader Windows - Clean
539 Knuckleboom Loader Cooling System Coolant Extender (ELC) - Add
539 Knuckleboom Loader Cooling System Coolant (ELC) - Change
517 Track-Type Skidder Leaving the Machine
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Troubleshooting - Engine
539 Knuckleboom Loader Swing Bearing - Lubricate
539 Knuckleboom Loader Engine Air Filter Primary Element - Clean/Replace
539 Knuckleboom Loader Engine Air Filter Secondary Element - Replace
539 Knuckleboom Loader Engine Air Precleaner - Clean
539 Knuckleboom Loader Engine Oil Level - Check
539 Knuckleboom Loader Engine Oil and Filter - Change
539 Knuckleboom Loader Fuses - Replace
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Warning Signs and Labels
Air Conditioning and Heating R134a for All Caterpillar Machines Refrigerant Expansion Valve System
527 Track-Type Skidder Shipping the Machine
784B Tractor and 785B Off-Highway Truck Power Train Lockup Clutch and Synchronizing Valve (Torque Converter)
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Check Valve