938F WHEEL LOADER POWER TRAIN Caterpillar


Differential (Limited Slip)

Usage:

Disassemble Differential (Limited Slip)

Start By:

a. remove differentials and pinion assemblies

NOTE: DO NOT use this procedure with limited slip differential Part Nos. 103-2008 and 144-4464. Refer to "Disassemble & Assemble Differential (Limited Slip) (Part Nos. 103-2008 & 144-4464)" in this module.

1. Remove two socket head bolts (3). Turn the differential up on differential housing cover (1), and remove differential housing (2).

2. Remove thrust washer (4), two outer discs (5), two inner discs (6) and pressure ring (7).

3. Remove bevel gear (8).

4. Remove four bevel pinions (10) and two pinion shafts (9).

5. Remove bevel gear (12), pressure ring (11), two outer discs (13), two inner discs (14) and thrust washer (15).

Assemble Differential (Limited Slip)

NOTE: DO NOT use this procedure with limited slip differential Part Nos. 103-2008 and 144-4464. Refer to "Disassemble & Assemble Differential (Limited Slip) (Part Nos. 103-2008 & 144-4464)" in this module.

1. Put differential housing cover (1) in the position shown.

2. Install thrust washer (15), two inner discs (14), two outer discs (13), ring (11) and bevel gear (12) on differential housing cover (1).

3. Install bevel gears (10) on pinion shafts (9). Install the bevel gears and pinion shafts on the pressure ring.

4. Install bevel gear (8).

5. Install pressure ring (7), two inner discs (6), two outer discs (5) and thrust washer (4).

6. Install differential housing (2). Install two socket bolts (3). Tighten socket head bolts to a torque of 54 ± 10 N·m (40 ± 7 lb ft).

7. Check the endplay. Replace the inner and outer discs, as necessary, to maintain an endplay of 0.5 ± 0.3 mm (0.20 ± .012 in) after assembly.

NOTE: The thickness of the 8R-9741 disc [outer (new)] is 3.00 mm (.118 in). The thickness of the 8R-9740 disc [outer (new)] is 2.90 mm (.114 in). The thickness of the 8R-9742 disc [outer (new)] is 3.10 mm (.122 in). The thickness of the 8R-9743 disc [outer (new)] is 3.00 mm (.118 in).

NOTE: Average the stack heights of (A) & (B). The difference must be within 0.10 mm (.004 in).

End By:

a. install differentials and pinion assemblies

Disassemble Differential (Limited Slip) (Part Nos. 103-2008 & 144-4464)

Start By:

a. remove differential

NOTE: Use this procedure with limited slip differential Part Nos. 103-2008 and 144-4464. All others refer to "Disassembly & Assemble Differential (Limited Slip)" in this module.

1. Remove two bolts (1).

2. Remove case cover (2) from case housing (3).

3. Invert case cover (2) and remove thrust washer (4).

4. Measure the end play gap, as follows:

a. Install Tooling (A) on the differential assembly, as shown.

NOTE: The center pusher bolt of Tooling (A) must have M16 x 2.0 thread to apply the proper preload on the disc packs.

b. Tighten the center bolt of Tooling (A) to a torque of 27 N·m (20 lb ft) to apply 900 kg (2000 lb) of preload on the disc packs.

c. Mount the magnetic base of Tooling (B) on Face A of case cover (2).

d. Zero the dial indicator on Face B, as shown.

e. Carefully remove Tooling (B) from the case cover.

f. Mount the magnetic base of Tooling (B) on Face C of the differential case housing. Touch the dial indicator on the disc pack Face D.

g. Record the indicator reading.

h. Record two additional indicator readings from different areas of Face D.

i. Average the three indicator readings. This is the measured end play gap.

j. If the end play gap in Step 4i was greater than 0.81 mm (.032 in), replacement of the existing disc packs is necessary.

5. Remove the disc pack from the case housing. The disc pack consists of two friction disc (5) and two plates (6).

6. Remove actuator housing (7) and gear (8) from the case housing, as shown.

7. Remove pinion shaft (10) and two pinion gears (9).

8. Remove the remaining pinion shaft (12) and two pinion gears (11).

9. Remove two pinion gears (9) from pinion shaft (10). Repeat for the remaining pinion shaft (12) and pinion gears (11).

10. Remove gear (13) from the case housing.

11. Remove actuator housing (14) from the case housing by lifting straight upward, as shown.

12. Remove the disc pack from the case housing. The disc pack consists of two friction discs (16) and two plates (15).

13. Remove thrust washer (17).

Assemble Differential (Limited Slip) (Part Nos. 103-2008 & 144-4464)

NOTE: Use this procedure with limited slip differential Part Nos. 103-2008 and 144-4464. All others refer to "Disassembly & Assemble Differential (Limited Slip)" in this module.

1. Clean and inspect all parts of the differential. If any of the parts are worn or damaged, use new parts for replacement.

2. Install thrust washer (17) in the case housing. Lubricate the thrust washer face with clean axle oil.

3. Replace the disc packs if:

a. The stack heights of the disc packs are NOT symmetrical within 0.10 mm (.004 inch).

b. The disc friction material is worn such that the discs, or areas of the discs, are running steel on steel.

4. When replacement of the disc packs is required, replace with the disc packs of the same type. If THIN is marked on the case cover, replace with two new THIN disc packs. If THICK is marked on the case cover, replace with two new THICK disc packs. Do not mix disc packs. Use two THIN or two THICK. Do not use one of each.

NOTE: Use clean axle oil to thoroughly lubricate plates and friction discs, prior to assembly.

5. Install two friction discs (16) and two plates (15) in alternate order in the case housing starting with a plate and ending with a friction disc, as shown.

6. Align the keys of actuator housing (14) with the slots of the case housing and install, as shown.

7. Install gear (13) in the case housing.

NOTE: Turn the gear slowly until the spline engages with the two friction discs installed in Step 5. Make sure the gear is fully seated.

8. Install two pinion gears (9) on pinion shaft (10). Repeat for remaining pinion shaft (12) and two pinion gears (11). Lubricate with clean axle oil.

9. Install pinion shaft (12) and two pinion gears (11) in the case housing, as shown.

10. Rotate pinion gears (11) slightly until the pinion shaft rests in the V-slots of the actuator housing.

11. Install the remaining pinion shaft (10) and two pinion gears (9) in the case housing, as shown.

12. Assemble gear (8) and actuator housing (7) on bench, as shown. Align the keys of the actuator housing with the slots in the case housing and install, as shown.

NOTE: Use clean axle oil to thoroughly lubricate plates and friction discs, prior to assembly.

13. Install two friction discs (5) and two plates (6) in alternate order in the case housing starting with a friction disc and ending with a plate.

NOTE: Steps 14 through 22 describe the proper procedure for measuring end play gap.

14. Install tooling (A) on the differential assembly, as shown.

NOTE: The center pusher bolt of Tooling (A) must have M16 x 2.0 thread to apply the proper preload on the disc packs.

15. Tighten the center bolt of Tooling (A) to a torque of 27 N·m (20 lb ft) to apply 900 kg (2000 lb) of preload on the disc packs.

16. Mount the magnetic base of Tooling (B) on Face A of case cover (2).

17. Zero the dial indicator on Face B, as shown.

18. Carefully remove Tooling (B) from the case cover.

19. Mount the magnetic base of Tooling (B) on Face C of the differential case housing. Touch the dial indicator on the disc pack Face D.

20. Record the indicator reading.

21. Record two additional indicator readings from different areas of Face D.

22. Average the three indicator readings. This is the measured end play gap.

NOTE: If the existing disc packs were installed in Step 4, continue with Step 23. If new disc packs were installed in Step 4, continue with Step 24.

23. If the end play gap in Step 22 was greater than 0.81 mm (0.032 inch), replacement of the existing disc packs is necessary.

NOTE: Steps 24 though 28 are for new replacement disc packs.

24. When replacement of the disc packs is required, replace with disc packs of the same type. If THIN is marked on the case cover, replace with two new THIN disc packs. If THICK is marked on the case cover, replace with two new THICK disc packs. Do not mix disc packs. Use two THIN or two THICK. Do not use one of each.

25. With new disc packs installed in the limited slip differential, measure the end play gap as described in Steps 14 though 22. The measured end play gap must fall between 0.203 and 0.508 mm (.0080 and .0200 inch).

26. If the measured end play gap is greater than 0.508 mm (.0200 inch) and two THIN disc packs were installed, remove two THIN disc packs and install two THICK disc packs. Measure the end play gap again to determine if it falls between 0.203 and 0.508 mm (.0080 and .0200 in) to meet specifications.

27. If the measured end play gap still does not meet specifications, replace the pinion shafts and or both actuator housings. Install either two THIN or two THICK disc packs to obtain an end play gap that falls between 0.203 and 0.508 mm (.0080 and .0200 in) to meet specifications.

28. If the disc packs were changed from the kind marked on the outside surface of the case housing, replace the existing mark with either THICK or THIN for future reference.

29. Install thrust washer (4) in case cover (2). Lubricate the thrust washer face with clean axle oil.

NOTE: Apply a small amount of grease to the back side of the thrust washer prior to installing. This will retain the thrust washer in place when the case cover is installed.

30. Align case housing and cover stamp marks. Install case cover (2) on case housing (3).

30. Install two bolts (1). Tighten bolts (1) to a torque of 61 ± 7 N·m (45 ± 5 lb ft).

End By:

a. install differential

Caterpillar Information System:

938F WHEEL LOADER POWER TRAIN Differential (Standard)
938F WHEEL LOADER POWER TRAIN Pinion Assemblies
938F WHEEL LOADER POWER TRAIN Differentials & Pinion Assemblies
938F WHEEL LOADER POWER TRAIN Brake Groups
938F WHEEL LOADER POWER TRAIN Axle Shaft Assemblies
938F WHEEL LOADER POWER TRAIN Rear Support (Rear Axle Housing Group)
938F WHEEL LOADER POWER TRAIN Front Support (Rear Axle Housing Group)
938F WHEEL LOADER POWER TRAIN Rear Axle Housing Group (Oscillating)
938F WHEEL LOADER POWER TRAIN Front Axle Housing Group (Fixed)
938F WHEEL LOADER POWER TRAIN Traction Control System (TCS) Wheel Speed Sensors (rear)
938F WHEEL LOADER POWER TRAIN Traction Control System (TCS) Wheel Speed Sensors (front)
938F WHEEL LOADER POWER TRAIN Traction Control System (TCS) Articulation Angle Sensor
938F WHEEL LOADER POWER TRAIN Differential (NoSPIN)
938F WHEEL LOADER POWER TRAIN Engine
938F WHEEL LOADER POWER TRAIN Transmission Control Valve
938F WHEEL LOADER POWER TRAIN Transmission
938F WHEEL LOADER POWER TRAIN Torque Converter
938F WHEEL LOADER POWER TRAIN Transmission Magnetic Filter
938F WHEEL LOADER POWER TRAIN Flow Control Valve
938F WHEEL LOADER POWER TRAIN Drive Shaft Group
938F WHEEL LOADER IT38F INTEGRATED TOOLCARRIER STEERING SYST Introduction
938F WHEEL LOADER IT38F INTEGRATED TOOLCARRIER STEERING SYST Hydraulic Steering Pump 107-9532
938F WHEEL LOADER IT38F INTEGRATED TOOLCARRIER STEERING SYST Supplemental Steering Pump 113-2010
938F WHEEL LOADER IT38F INTEGRATED TOOLCARRIER STEERING SYST Metering Pump
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.