1980/02/04 Caterpillar


New Turbocharger Group Has A Water-Cooled Bearing Housing{1052,1053,1073,1380,1307}

Usage:


D9H And DD9H Tractors;
594H Pipelayers

SUPPLEMENT: 06/23/80

SERVICE MAGAZINE, FEBRUARY 4, 1980, PAGES 6 AND 7. In the article "New Turbocharger Group Has A Water-Cooled Bearing Housing" that starts on Page 6, change the "ADAPTABLE TO:" paragraph at the top of Page 7 to read:

Adaptable To: The new turbocharger and the new lines groups are adaptable to earlier machines with Engine Serial Numbers 97U7229-up when the parts shown in the chart are used together. Information about conversion of machines with earlier engines will be given in a future article when the necessary parts become available.

--------------- END SUPPLEMENT ---------------

Description of Change: A new turbocharger with a water-cooled bearing housing is used on engines for D9H and DD9H Tractors, and 594H Pipelayers. A new turbocharger water lines group and a new turbocharger oil lines group are also used with the new turbocharger.

This new turbocharger design keeps oil temperatures inside the bearing housing lower during operation and shutdown. This will prevent oil from coking in the oil passages.

Formerly, the high temperatures in the bearing housings of the former turbochargers some times permitted oil coking. This caused leakage around the seals, bearing failures and some times complete turbocharger failures.

Changes to another water lines group and the transmission oil cooler group give ports to supply and drain the new turbocharger water lines group.

The shield group has been changed to give clearance for the turbocharger oil lines group. These changes permit the use of the new turbocharger on earlier machines.

Caterpillar Information System:

1980/02/04 Shock Absorber Now Used In Belt Tightener Group{1358}
1980/02/04 New Bonnet Used On Transmission Oil Cooler; Bracket Holds Bonnet To Oil Pan{1375,1302}
1980/02/04 Real Value Available Through Caterpillar Remanufacturing Programs{0374}
1980/02/04 Change To Gear On Accessory Drive Shaft Assembly Gives Longer Service Life{1207,1206}
1980/02/04 New Cylinder Liner Has Improved Design To Keep Liner Temperatures Lower{1216}
1980/01/28 Oil Drain Hole Added To Spacer Plate Cylinder Block To Permit Use Of Scroll Fuel System{1201,1221}
1980/01/28 Installation Procedures For 5N5880 Remote Shut-Off Group And 5N6336 Oil Pressure Indicator Gauge Group{7418,7403,7455}
1980/01/28 Correct Planet Gear Bearings Must Be Used For Parts Service Of Transmission Gear Trains{3176}
1980/01/28 Different Seal For Control Shaft In Power Control Box{5201}
1980/01/28 Reinforcement Plates Can Be Added To Make The Fuel Tank Stronger{1273}
1980/01/28 New 6V199 Socket For Use On Fasteners In Areas With Limited Clearance{0612}
1980/01/28 Radiator Fan Blades Can Be Damaged If They Come In Contact With Large Quantities Of Water{1356}
1980/02/04 Different Nuts Now Used To Adjust Preload On Bearings For Differential And Bevel Gears{3258,3256,3257}
1980/02/11 Warning: Avoid Use Of Fuel Mixtures Of High Volatility. If You Are Exposed To Such Mixtures, Be Aware Of The Hazards Involved And Take Proper Precautions{1280}
1980/02/11 New Bearing Retainer Plate Is Used In Carrier Rollers{4154}
1980/02/11 New Gasket Gives A Better Seal Between The Flywheel Housing And Cylinder Block{1157,1201}
1980/02/11 Use The Correct Water Temperature Contactor{1350,1100}
1980/02/11 Improved Wheel Assembly (Stator) Used In Torque Converters{3101}
1980/02/11 New Bypass Valve Used In Oil Filters{3179,5068,3004}
1980/02/11 Locknuts And Hardened Washers Now Used On The Differential Housing Retainer Bolts; Torque Value Increased{3258}
1980/02/25 SAE 30 Oil Now Used In Swing Drive And Final Drive{5459,4070}
1980/02/25 New Weld Inspection Gauges for Track Rollers And Idlers{0653,4159,4180}
1980/02/25 Revision Of Special Instruction Form No. SMHS7267, "Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets" Has Important Changes{1307}
1980/02/25 Stronger Braces Used Between Air Cleaner And Engine{1051}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.