Final Drive - Assemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 554-5076 | 扭矩倍增器 | 1 |
D | 554-5070 | 密封件安装工具 | 1 |
E | 4C-8359 | 吊环螺栓 | 2 |
注: 清洁度是一项重要的因素。 组装之前,应使用清洁液体彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零件。 棉绒可能会留在零件上,可能导致以后出现故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。
- 使用适当的工具定位轴承座圈 (15)。 安装轴承座圈 (15)。
Show/hide table
图 2 g06269638 - 将轴承滚珠 (17) 和支架安装到壳体中。
Show/hide table
图 3 g06269643 注: 密封件及与密封件接触的所有表面必须清洁、干燥。 安装密封件后,在密封件的接触面上涂上机油。
- 将轴承座圈 (13) 安装到壳体中。
Show/hide table
图 4 g06269646 Show/hide table图 5 g06269647 Show/hide table图 6 g06269761 密封件 (14) 的方位。
尺寸 (X) 等于0.5 mm (0.02 inch) 。 - 使用工具 (D) 安装密封件 (14)。 将密封件 (14) 安装到壳体 (12) 中。 密封件 (14) 的平整度应与尺寸 (X) 相同。
Show/hide table
图 7 g06269650 Show/hide table图 8 g06269760 密封件 (15) 的方位。
尺寸 (Y) 等于0.5 mm (0.02 inch) 。 - 使用工具 (D) 安装密封件 (15)。 将密封件 (15) 安装到行驶马达 (11) 中。 密封件 (14) 的平整度应与尺寸 (Y) 相同。
Show/hide table
图 9 g06269651 - 清洁密封件 (14) 表面。
Show/hide table
图 10 g06269652 - 将工具 (E) 和适当的起吊设备固定到行驶马达 (11) 上。 行驶马达 (11) 的重量约为
125 kg (276 lb) 。 将行驶马达 (11) 定位到壳体中。Show/hide table图 11 g06269653 Show/hide table图 12 g06272894 典型示例 注: 使用成 180 度的两个卡箍,以避免移动装置期间,壳体 (12) 从行驶马达 (11) 上脱开。 定位装置时,拆下卡箍。
- 使用适当的压具和金属止动块安装行驶马达 (11)。 安装行驶马达 (11)。
Show/hide table
图 13 g06269611 - 将环形螺母 (10) 放置到壳体中。
Show/hide table
图 14 g06269655 - 使用适当的起吊设备将工具 (A) 放置到环形螺母 (10) 上。 通过扭矩扳手拧紧,使输入乘数扭矩
143 ± 5 N·m (105 ± 4 lb ft) 对应于输出乘数扭矩7750 ± 250 N·m (5716 ± 184 lb ft) 。Show/hide table图 15 g06269656 - 安装隔套 (9)。
Show/hide table
图 16 g06269663 Show/hide table图 17 g06269664 - 将齿轮 (8) 放置到法兰轮毂上。
- 使用橡胶锤和金属止动块安装齿轮 (8)。 安装齿轮 (8)。
Show/hide table
图 18 g06269606 - 安装挡圈 (7)。
Show/hide table
图 19 g06269605 - 安装行星齿轮组件 (6)。
Show/hide table
图 20 g06269604 - 安装太阳齿轮 (5)。
Show/hide table
图 21 g06269603 - 安装 O 形密封圈 (4)。
Show/hide table
图 22 g06269602 - 安装盖 (3)。
Show/hide table
图 23 g06269601 - 安装螺栓 (2)。 拧紧螺栓 (2) 至扭矩为
70 ± 7 N·m (52 ± 5 lb ft) 。Show/hide table图 24 g06269665 - 向终传动中加注润滑油。 将螺塞 (18) 插入盖的机油排放和加注孔。
- 拧紧螺塞 (18) 至扭矩为
35 ± 5 N·m (310 ± 44 lb in) 。
Show/hide table
图 1 | g06272616 |
Caterpillar Information System:
C7.1 Marine Propulsion Engine Engine Oil Pan - Remove and Install
320D2 Excavator Machine Systems Final Drive - Disassemble
C7.1 Marine Propulsion Engine Engine Oil Cooler - Remove and Install
320D2 Excavator Machine Systems Swing Drive - Assemble
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Track Adjustment - Inspect
C7.1 Marine Propulsion Engine Belt Tensioner - Remove and Install
320D2 Excavator Machine Systems Swing Drive - Disassemble
New Software Is Now Used on Certain G3516H and G3520H Engines {1920} New Software Is Now Used on Certain G3516H and G3520H Engines {1920}
Installation Instruction on Aluminum Oil Pan Baffle Isolators Certain C175 Locomotive Engines {1302} Installation Instruction on Aluminum Oil Pan Baffle Isolators Certain C175 Locomotive Engines {1302}
320D3 Hydraulic Excavator Machine Systems Final Drive and Travel Motor - Remove and Install
C280-12 Marine Engine Ordering Replacement Parts
C7.1 Marine Propulsion Engine Crankshaft Rear Seal - Remove and Install
C7.1 Marine Propulsion Engine Engine Oil Pump - Remove and Install
C7.1 Marine Propulsion Engine Engine Oil Pan Plate - Remove and Install
C7.1 Marine Propulsion Engine Front Cover - Remove and Install
C7.1 Industrial Engine Engine Air Cleaner Element - Replace
C9.3B Aftertreatment Systems SCR Catalyst Sulfation Is Excessive
C9.3B Aftertreatment Systems SCR Inducement Emergency Override
G3512H and G3516H Generator Set Engines Engine Oil Cooler - Remove and Install
M0090131 Battery Analyzer 480-4181 (484-4859 Group) {0374, 0599, 0709, 1401, 7468} M0090131 Battery Analyzer 480-4181 (484-4859 Group) {0374, 0599, 0709, 1401, 7468}
C7.1 Marine Propulsion Engine Gear Group (Front) - Remove and Install
336 Excavators (Powered by C9.3 Tier 4 Engine) Engine Supplement Water Pump - Remove and Install
C9.3B Engine Intake Manifold Air Temperature Is Low
C9.3B Engine Fuel Temperature Is High