Swing Drive - Assemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 3E-3879 | 吊环螺栓 | 2 |
B | 554-5075 | 扭矩倍增器 | 1 |
C | 554-5069 | 拉拔器套件 | 1 |
D | 554-5067 | 密封圈组件 | 1 |
E | 554-5068 | 止动块 | 1 |
F | - | Loctite 243 | - |
G | 452-6011 | 润滑脂 | - |
注: 清洁度是一项重要的因素。 组装之前,应使用清洁液体彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零件。 棉绒可能会留在零件上,可能导致以后出现故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。
- 使用工具 (D) 和橡胶锤安装密封件 (20)。 安装密封件 (20)。
Show/hide table
图 3 g06269306 - 倒置减速器壳体 (15),并加注工具 (G)。
Show/hide table
图 4 g06269307 - 将隔套 (18) 和密封圈 (17) 安装到小齿轮轴上。
Show/hide table
图 5 g06269308 - 将工具 (G) 涂覆到密封圈 (17) 上。
Show/hide table
图 6 g06269309 - 将轴承 (16) 插到小齿轮轴上。
Show/hide table
图 7 g06269310 - 使用适当的压具和工具 (E) 安装轴承 (16)。 安装轴承 (16)。
Show/hide table
图 8 g06269311 - 将工具 (G) 涂覆到轴承 (16) 上。
Show/hide table
图 9 g06269312 - 将适当的起吊设备连接到小齿轮轴 (14) 上。 小齿轮轴 (14) 与轴承组件的重量约为
33 kg (73 lb) 。 将小齿轮轴组件定位到工具 (C) 上。Show/hide table图 10 g06269315 Show/hide table图 11 g06269316 - 将工具 (A) 和适当的起吊设备连接到减速器壳体 (15) 上。 减速器壳体 (15) 的重量约为
69 kg (152 lb) 。 将减速器壳体 (15) 定位到小齿轮轴上。 - 使用适当的压具和工具 (E) 安装壳体 (15)。 安装壳体 (15)。
Show/hide table
图 12 g06269317 Show/hide table图 13 g06269318 - 使用适当的压具和工具 (E) 安装轴承 (18)。 安装轴承 (18)。
Show/hide table
图 14 g06269319 - 将工具 (F) 涂覆到环形螺母 (13) 的螺纹上。
Show/hide table
图 15 g06269322 Show/hide table图 16 g06269324 - 使用适当的起吊设备将工具 (B) 放置到环形螺母 (13) 上。 通过扭矩扳手拧紧,使输入乘数扭矩
60 ± 3 N·m (44 ± 2 lb ft) 对应于输出乘数扭矩1800 ± 100 N·m (1328 ± 74 lb ft) 。Show/hide table图 17 g06269325 - 由两个人一起安装行星齿轮组件 (9)。 行星齿轮组件 (9) 的重量约为
33 kg (73 lb) 。 安装行星齿轮组件 (9)。Show/hide table图 18 g06269326 - 安装 O 形密封圈 (12)。
Show/hide table
图 19 g06269328 注: 确保齿圈 (11) 安装正确。 旋转齿圈 (11) 将导致 O 形密封圈损坏。
- 安装齿圈 (11)。
Show/hide table
图 20 g06269329 - 安装 O 形圈 (10)。
Show/hide table
图 21 g06318529 - 将太阳齿轮 (8A) 和挡圈 (8) 安装到行星齿轮组件中。
Show/hide table
图 22 g06269331 - 安装行星齿轮组件 (7)。
Show/hide table
图 23 g06269335 - 安装太阳齿轮 (6)。
Show/hide table
图 24 g06269332 Show/hide table图 25 g06269334 - 安装盖 (5) 和螺栓 (4)。
Show/hide table
图 26 g06269336 - 安装 O 形密封圈 (3)。
Show/hide table
图 27 g06269514 X - 2.5 mm
Y -61.5 mm to 62.3 mm - 如果值不正确,请按照以下步骤操作
- 值较高:减小太阳齿轮 (6) 在轴向方向上的宽度,使支撑平面变平。
- 值较低:在太阳齿轮 (6) 和行星齿轮组件 (7) 之间引入调节隔套。
Show/hide table图 28 g06269281 - 使用适当的起吊设备以定位回转马达 (1)。 回转马达 (1) 的重量约为
50 kg (110lb) 。 安装回转马达 (1) 和螺栓 (2)。
Show/hide table
图 1 | g06269304 |
Show/hide table
图 2 | g06269305 |
Caterpillar Information System:
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Track Adjustment - Inspect
C7.1 Marine Propulsion Engine Belt Tensioner - Remove and Install
320D2 Excavator Machine Systems Swing Drive - Disassemble
New Software Is Now Used on Certain G3516H and G3520H Engines {1920} New Software Is Now Used on Certain G3516H and G3520H Engines {1920}
Installation Instruction on Aluminum Oil Pan Baffle Isolators Certain C175 Locomotive Engines {1302} Installation Instruction on Aluminum Oil Pan Baffle Isolators Certain C175 Locomotive Engines {1302}
320D3 Hydraulic Excavator Machine Systems Final Drive and Travel Motor - Remove and Install
C280-12 Marine Engine Ordering Replacement Parts
C7.1 Marine Propulsion Engine Crankshaft Rear Seal - Remove and Install
320D3 Hydraulic Excavator Machine Systems Swing Motor and Swing Drive - Remove and Install
Troubleshooting for Oil Carry Over from Side Mounted Breathers {1074, 1317} Troubleshooting for Oil Carry Over from Side Mounted Breathers {1074, 1317}
320, 323 and 330 Excavator Long Reach Front Cylinder Speed - Test and Adjust
320, 323 and 330 Excavator Long Reach Front Relief Valve (Line) - Test and Adjust
C7.1 Marine Propulsion Engine Engine Oil Cooler - Remove and Install
320D2 Excavator Machine Systems Final Drive - Disassemble
C7.1 Marine Propulsion Engine Engine Oil Pan - Remove and Install
320D2 Excavator Machine Systems Final Drive - Assemble
C7.1 Marine Propulsion Engine Engine Oil Pump - Remove and Install
C7.1 Marine Propulsion Engine Engine Oil Pan Plate - Remove and Install
C7.1 Marine Propulsion Engine Front Cover - Remove and Install
C7.1 Industrial Engine Engine Air Cleaner Element - Replace
C9.3B Aftertreatment Systems SCR Catalyst Sulfation Is Excessive
C9.3B Aftertreatment Systems SCR Inducement Emergency Override
G3512H and G3516H Generator Set Engines Engine Oil Cooler - Remove and Install
M0090131 Battery Analyzer 480-4181 (484-4859 Group) {0374, 0599, 0709, 1401, 7468} M0090131 Battery Analyzer 480-4181 (484-4859 Group) {0374, 0599, 0709, 1401, 7468}