Bucket Cylinder
Show/hide table
图 1 | g06239787 |
液压铲斗油缸 (1) 铲斗油缸 (2) 缸盖端端口 (3) 连杆端端口 |
铲斗油缸开启和闭合铲斗。 当液压油流入铲斗油缸的缸盖端端口 (2) 时,油缸伸出。 从而使铲斗闭合。 当液压油流入铲斗油缸的连杆端端口 (3) 时,油缸缩回。 从而使铲斗打开。
Show/hide table
图 2 | g06239794 |
铲斗油缸的剖面图 (4) 盖 (5) 油缸壳体 (6) 杆 (7) 活塞 (8) 锁紧螺母 |
缸盖端端口 (2) - 允许油流入油缸缸盖端,以便伸出油缸。
连杆端端口 (3) - 允许油流入油缸连杆端,以便缩回油缸。
盖 (4) - 缸盖包含用于保持液压的密封件,并在缩回时保持连杆清洁。
油缸壳体 (5) - 油缸壳体包含作为密封设备的内部零件。
杆 (6) - 连杆伸出和缩回,以便打开和关闭铲斗。
活塞 (7) - 加压油向活塞施加压力,以便缩回和伸出油缸。
锁紧螺母 (8) - 将活塞固定到连杆上。
Show/hide table
图 3 | g06239802 |
活塞环和密封件 (9) 承磨环 (10) 承磨环 (11) 活塞油封 |
承磨环 (9) 和 (10) 为活塞提供支承面并防止活塞接触油缸壳体的内径。 承磨环 (10) 还用作阻火器。
活塞密封 (11) 阻止机油在油缸壳体和活塞之间流动。
注: 在 GC 机器上,通过两个支承环将活塞密封件保持到位。
Show/hide table
图 4 | g06239805 |
连杆/缸盖密封件和轴承 (12) 刮油密封环 (13) U 形密封件 (14) 缓冲密封件 (15) 轴承套筒 (16) 挡圈 (17) O 形密封圈 (18) 支承环 (19) 支承环 |
轴承套筒 (15) 为连杆提供支承面并防止油缸缸盖磨损。 挡圈 (16) 将轴承套筒固定到位。
缓冲密封件 (14) 是第一个承压密封件。 缓冲密封件旨在减小 U 形油封 (13) 和支承环 (19) 上的压力峰值,以延长寿命。
U 形油封 (13) 从外部阻止机油流经油缸缸盖。 密封件还阻止外部油液进入油缸。
刮油密封环 (12) 有一个朝外的唇形密封,可以在缩回期间刮去连杆上的碎屑。 刮油密封环旨在防止颗粒进入油缸。
O 形圈 (17) 防止油缸壳体 (5) 和缸盖 (4) 之间发生漏油。 支承环 (18) 将 O 形圈固定到位。
Caterpillar Information System:
XQ125 Generator Set Cooling System Coolant Level - Check
XQ125 Generator Set Belt Tensioner - Inspect
XQ125 Generator Set Cooling System Coolant (DEAC) - Change
320 GC, 320, 323, 330 GC and 330 Excavator Machine Systems Troubleshooting Sensor Supply - Test - Display
320 GC, 320, 323, 330 GC and 330 Excavator Machine Systems Troubleshooting Ethernet Data Link - Test
320 GC, 320, 323, 330 GC and 330 Excavator Machine Systems Troubleshooting ECM Location Code - Test
336, 336 GC and 340 Excavator Systems Sensor (Data Link Type) - Test
XQ125 Generator Set Stopping the Engine
XQ125 Generator Set Sensors and Electrical Components
C32 Marine Engines Crankshaft Main Bearings - Install
C32 Marine Engines Engine Oil Pan - Remove and Install
New Firmware is Available for 7 inch and 13 inch Displays for Certain Marine Engines {7490, 7620} New Firmware is Available for 7 inch and 13 inch Displays for Certain Marine Engines {7490, 7620}
320GC and 320 Excavator Engine Supplement Manifold (DEF Heater) - Remove and Install
C32 Marine Engines Speed/Timing Sensor - Remove and Install
C32 Marine Engines Inlet Manifold Pressure Sensor - Remove and Install
C32 Marine Engines Inlet Air Temperature Sensor - Remove and Install
320GC and 320 Excavator Engine Supplement Nitrogen Oxide Sensor - Remove and Install
336, 336 GC and 340 Excavator Systems Stick Cylinder
The Buffer Seal Groove May Wear on the Steering Cylinder Head on Certain 773G and 777G Off-Highway Trucks {4303} The Buffer Seal Groove May Wear on the Steering Cylinder Head on Certain 773G and 777G Off-Highway Trucks {4303}
C7.1 Marine Engine Exhaust Elbow - Remove and Install
C7.1 Engines Coolant Pressure Is Low
336, 336 GC and 340 Excavator Systems Pilot System
C32 Marine Engines Electronic Control Module - Remove and Install
794 AC Off-Highway Truck Magnetic Plug (Wheels) - Check