Diagnostic Flash Code Retrieval
The multi-function lamp will flash a two or a three-digit code in a given sequence to show the flash code diagnostic massage. By counting the number of flashes in a given sequence, you can determine the flash code.
After the flash code as finished, the flash code sequence will continual to be repeated. If a second flash code has been activated, then the system will repeat both codes in the given sequence.
Four short flashes will indicate a flash code of 04. Three long flashes of one second each followed by one short flash will indicate a flash code of 31.
- APS ____________________Actuator Power Supply
- CPU ____________________Central Processing Unit (Engine controller)
- MAP ____________________Manifold Air Pressure
Show/hide table
Diagnostic Flash Codes | |||
Flash Code | Diagnostic Description | Latched to Next Key Cycle | Engine Shut-down |
04 | Actuator Out Put Overcurrent | - | - |
13 | Oil Pressure Switch Issue | Yes | Yes |
15 | MPU Sensor Failure | - | Yes |
17 | Battery Voltage Over High Threshold | - | - |
18 | Battery Voltage Below Low Threshold | - | - |
22 | Air Pressure Sensor Out of Range | - | - |
31 | Engine Oil Pressure Low | - | Yes |
32 | Actuator Mechanically Stuck | - | Yes |
33 | Actuator Position Sensor Out of Range | - | Yes |
40 | Actuator Output Overcurrent | - | Yes |
51 | Internal Hardware Failure | - | Yes |
52 | Device Configuration Corrupted | - | Yes |
53 | Controller Internal Supply Dropout | - | - |
54 | (EEPROM) Read/Write Internal Hardware Failure | - | - |
55 | APS J1-J2 Pin Short to Ground | - | Yes |
543 | (Overspeed) engine speed Limit Exceeded | - | Yes |
For more information contact your Cat dealer.
Caterpillar Information System:
C0.5 and C0.7 Industrial Engines Overspeed
C0.5 and C0.7 Industrial Engines Gauges and Indicators
C0.5 and C0.7 Industrial Engines Emissions Certification Film
320GC and 320 Excavator Engine Supplement Diesel Exhaust Fluid Pump - Remove and Install
745 and 740 GC & 740 EJECTOR Articulated Truck Systems Temperature Sensor - Brake Cooling Oil and Hydraulic Tank
320GC, 320 and 323 Excavators Machine Systems Stick Bearings and Seals - Remove and Install
320 GC, 320 and 323 Excavator Machine Systems Relief Valve (Cushion Crossover) - Anti-Reaction Valve
C9.3B Engines for Caterpillar Built Machines Lifter Group - Remove and Install
G3516 Petroleum Engine Fluid Recommendations
320 GC, 320 and 323 Excavator Machine Systems Solenoid Valve (Fine Swing) - If Equipped
G3516 Petroleum Engine Overhaul (In-Frame)
C0.5 and C0.7 Industrial Engines Maintenance Interval Schedule
New Engine Software is Now Available for 3512C Engines Used On Certain Mining Shovels {7620} New Engine Software is Now Available for 3512C Engines Used On Certain Mining Shovels {7620}
Certain Cat® Reman Fuel Injectors May be Marked with Incorrect Trim Codes {1251, 1254, 1290, 1713} Certain Cat® Reman Fuel Injectors May be Marked with Incorrect Trim Codes {1251, 1254, 1290, 1713}
3512E Engines Fuel Control Valve - Remove and Install - Primary
C0.5 and C0.7 Industrial Engines Starting the Engine
C0.5 and C0.7 Industrial Engines Stopping the Engine
120 and 120 AWD Motor Grader Maintenance Interval Schedule
C0.5 and C0.7 Industrial Engines Refill Capacities
New Water Temperature Regulators Available {1355} New Water Temperature Regulators Available {1355}
C9.3B Engines for Caterpillar Built Machines Camshaft - Remove
G3500H Generator Set Engine Fuel Differential Pressure Is Low
320 GC, 320 and 323 Excavator Machine Systems Joystick and Pedal - Calibrate
320GC, 320 and 323 Excavators Machine Systems Boom Bearings and Seals - Remove and Install