Piston and Rings
Show/hide table
Illustration 1 | g06194959 |
388-2310 Piston Body As (6) |
Show/hide table
Specification for 452-9086 Piston and Rod Gp | |||
---|---|---|---|
Item | Qty | Part | Specification Description |
1 | 1 | 415-7459 Piston Ring | Install with side marked "UP-1" toward top of the piston. The colored stripe faces to the right of the piston ring end gap. |
Thickness of new top piston ring is |
|||
Clearance of the ends when assembled in a new cylinder liner of bore |
|||
2 | 1 | 331-6025 Piston Ring | Install with side marked "UP-2" toward top of the piston. The colored stripe faces to the right of the piston ring end gap. |
Thickness of new piston ring is |
|||
Width (A) of the groove in the piston for piston is |
|||
Clearance of the ends when assembled in a new cylinder liner of bore |
|||
3 | 1 | 265-1113 Piston Ring | The ends of the spring coil should be placed 180 degrees from the end gap of the oil control piston rings. The colored stripe in the spring coil must be visible at the oil control piston ring end gap. |
Thickness of new oil control piston ring is |
|||
Width (B) of the groove in the piston is |
|||
Clearance of the ends when assembled in a new cylinder liner of bore |
|||
- | After installing the piston rings, rotate the piston rings so that the end gaps are placed at 120 degrees distance from each other. | ||
Lubricate the entire piston to 360 degrees in zone (C) prior to assembly into the cylinder block. Use clean engine oil. | |||
4 | 1 | 197-9327 Piston Pin | Thoroughly lubricate the piston pin with clean engine oil prior to assembly. |
Diameter is Length is |
|||
Bore (D) in the piston body (6) for the piston pin is |
|||
5 | 2 | 197-9326 Retainer | Install the pin retainer with the opening towards top of the piston as shown in Illustration 1 |
Caterpillar Information System:
C11 and C13 Industrial Engines Cylinder Head
C9.3B Engines for Caterpillar Built Machines Housing (Front) - Remove
323F LN MHPU Capacities (Refill)
320 GC, 320 and 323 Excavator Machine Systems Travel Motor
320 GC, 320 and 323 Excavator Machine Systems Oil Makeup (Travel System)
C11 and C13 Engines Cylinder Head Valves
C175-16 Locomotive Engines Crankshaft Vibration Damper seals - Replace
C13, C15, and C18 Tier 4 Final Engines SCR Inducement Emergency Override
Different Housings are Used on 3400 Remanufactured Engines {1304} Different Housings are Used on 3400 Remanufactured Engines {1304}
C11 and C13 Engines Cylinder Liner
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System System Schematic
793F and 797F Off-Highway Truck VIMS and Truck Payload Measurement System Glossary of Terms
A New Reducer Hose Is Used on Certain 3512C Commercial Engines {1051} A New Reducer Hose Is Used on Certain 3512C Commercial Engines {1051}
3500E Marine Engines Inlet Manifold
3500E Marine Engines Inlet Manifold
G3516 Petroleum Engines Fuel Control Valve - Remove and Install - Low Pressure
3500E Marine Engines Cylinder Head
C9.3B Engines for Caterpillar Built Machines Housing (Front) - Install
320 GC, 320 and 323 Excavator Machine Systems Swing System
3500E Marine Engines Cylinder Block
320GC, 320 and 323 Excavators Machine Systems Swing Drive - Disassemble
320GC, 320 and 323 Excavators Machine Systems Swing Drive - Assemble
3516E Generator Set Engines Pressure Sensor (DEF)
3500E Marine Engines Exhaust Manifold