Engine Oil Pump - Remove
Start By:
- Remove the alternator.
Show/hide table
Required Tools | |||
Tools | Part Number | Part Description | Qty. |
A | 384-9657 | Lifting Eye Assembly | 1 |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog", for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Inspect all O-rings, seals, and gaskets for wear or damage. Replace if necessary.
- Remove flange bolts (1) at both ends and remove clip (2).
- Remove tube (3).
Show/hide table
Illustration 2 g06321672 - Remove bolts (4) and remove clips (5).
- Remove tube (6).
- Disconnect harness assembly (18) and position out of the way.
Show/hide table
Illustration 3 g06167770 - Disconnect sensors (7) and bolts (8).
- Remove intake manifold (9).
Show/hide table
Illustration 4 g06167809 - Disconnect hose (10) and set off to the side.
- Remove bolts (11), bolts (12), bolts (14) , and remove the elbow assembly (13).
Show/hide table
Illustration 5 g06167830 - Remove bolts (15).
Show/hide table
Illustration 6 g06167863 - Attach Tooling (A) at position (X). The engine oil pump (17) weighs approximately
55 kg (121 lb) . - Remove bolts (16) and remove the engine oil pump (17).
Show/hide table
Illustration 1 | g06167377 |
Caterpillar Information System:
Selective Catalytic Reduction Retrofit Aftertreatment - Airless Dosing Electronic Service Tools
Selective Catalytic Reduction Retrofit Aftertreatment - Airless Dosing Welding Precaution
3516B Generator Set Engines with Dynamic Gas Blending Centrifugal Oil Filters
Selective Catalytic Reduction Retrofit Aftertreatment - Airless Dosing General Information
Marine Selective Catalytic Reduction (SCR) Retrofit Aftertreatment Catalyst (SCR) - Replace
C8.7 and C12.9 Marine Engines Speed/Timing - Test
3516B Generator Set Engines with Dynamic Gas Blending Electronic Control Module (ECM) - In Cylinder Pressure Sensor (ICPS) ECM
3516B Generator Set Engines with Dynamic Gas Blending CAN Data Link
Radiator Fan Cracking or Breakage May Occur on Certain 3512 and 3516 Petroleum Engines {1356, 1360} Radiator Fan Cracking or Breakage May Occur on Certain 3512 and 3516 Petroleum Engines {1356, 1360}
Marine Selective Catalytic Reduction (SCR) Retrofit Aftertreatment Fluid Recommendations
XQP60 and XQP100 Rental Generator Sets Refill Capacities
Marine Selective Catalytic Reduction (SCR) Retrofit Aftertreatment Monitoring System
Selective Catalytic Reduction Retrofit Aftertreatment - Airless Dosing Component Location
Marine Selective Catalytic Reduction (SCR) Retrofit Aftertreatment Warranty Information
Selective Catalytic Reduction Retrofit Aftertreatment - Airless Dosing Diagnostic Capabilities
Selective Catalytic Reduction Retrofit Aftertreatment - Airless Dosing Electrical Connectors
Selective Catalytic Reduction Retrofit Aftertreatment - Airless Dosing Configuration Parameters
Selective Catalytic Reduction Retrofit Aftertreatment - Airless Dosing Diagnostic Trouble Codes
Selective Catalytic Reduction Retrofit Aftertreatment - Airless Dosing DEF Control Module Temperature Is High
Selective Catalytic Reduction Retrofit Aftertreatment - Airless Dosing DEF Module Does Not Respond
Selective Catalytic Reduction Retrofit Aftertreatment - Airless Dosing DEF Tank Level Is Low
Selective Catalytic Reduction Retrofit Aftertreatment - Airless Dosing Data Link - Test
C8.7 and C12.9 Marine Engines Sensor Supply - Test
323F SA and 323F LN Excavator Declaration of Conformity