Event Code List
Portions of this material are reprinted with permission from SAE J1939DA_201607© 2016 SAE International. SAE International is not responsible for any use or translation of this material, in whole or in part. Contact SAE International to obtain a complete copy of SAE J1939DA_201607, the official definitive source of this standard.
Show/hide table
| Event Codes for Transmission ECU | |
|---|---|
| DTC | Events |
| 120-0 | High Torque Converter Out Oil Temperature |
| 124-0 | Oil Level High |
| 124-1 | Oil Level Low |
| 177-16 | High Transmission Oil Temperature |
| 3823-16 | High Torque Converter Out Oil Temperature |
| 166-15 | Engine Rated Power: High |
| 168-1 | Battery Potential / Power Input #1: Low |
| 3359-16 | Trans Filter Plugged |
| 5877-16 | Trans Slip Detected in 1F |
| 5878-16 | Trans Slip Detected in 2F |
| 5879-16 | Trans Slip Detected in 3F |
| 5880-16 | Trans Slip Detected in 4F |
| 5881-16 | Trans Slip Detected in 5F |
| 5882-16 | Trans Slip Detected in 6F |
| 5883-16 | Trans Slip Detected in 7F |
| 5884-16 | Trans Slip Detected in 8F |
| 5885-16 | Trans Slip Detected in 9F |
| 5887-16 | Trans Slip Detected in 1R |
| 5888-16 | Trans Slip Detected in 2R |
| 3030-16 | Trans LUC slip detected in direct drive |
| 124-0 and 124-1 | Oil Level |
| 127-1 | Transmission Oil Pressure: Low |
| 191-16 | Transmission Over Speed |
| 191-14 | Transmission Output Speed Mismatch |
Caterpillar Information System:
CX38-P892 Well Servicing Transmission Diagnostic Capabilities
CX38-P892 Well Servicing Transmission Connector Locations
CX38-P892 Well Servicing Transmission Service Tools
CX38-P892 Well Servicing Transmission General Information
CX38-P892 Well Servicing Transmission System Schematic
CX38-P892 Well Servicing Transmission Transmission - Calibrate
CX38-P892 Well Servicing Transmission Speed Sensor - Adjust
CX38-P892 Well Servicing Transmission Electronic Control Unit - Replace
CX38-P892 Well Servicing Transmission Electronic Control Unit - Configure
CX38-P892 Well Servicing Transmission Electronic Control Unit - Flash Program
CX38-P892 Well Servicing Transmission Wiring Harness (Short Circuit) - Test
CX38-P892 Well Servicing Transmission Wiring Harness (Open Circuit) - Test
CX38-P892 Well Servicing Transmission Engine Does Not Crank
G3516 Petroleum Engines Rocker Shaft and Push Rod - Remove
C7.1 Marine Propulsion Engine Crankshaft
C175-16 Marine Engines Engine Governing - Adjust
G3516 Petroleum Engines Rocker Shaft and Push Rod - Install
New Heat Shields Are Now Used on Certain 3512 Locomotive Engines {1067, 7274} New Heat Shields Are Now Used on Certain 3512 Locomotive Engines {1067, 7274}
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Aftercooler - Remove and Install - Aftercooler Housing with 24 bolts
3500B Generator Sets Voltage Regulators
3516B Generator Set Engines with Dynamic Gas Blending Electronic Control System Operation
3516B Generator Set Engines with Dynamic Gas Blending Engine Monitoring System
G3516 Petroleum Engines Cylinder Head - Remove
CX38-P892 Well Servicing Transmission Transmission Does Not Automatically Shift Into Neutral