Procedure to Install SOLAS Tape On Certain 3516B Engines Fuel Rails {1252, 1274, 1702}
- Engine
- 3516B (S/N: BCK1-UP)
Introduction
Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.
Installation Procedure
- Cut
139.7 mm (5.5 inch) long piece of 237-3860 Tape and fold it long ways.Note: Once SOLAS tape comes in contact with itself or another piece of tape, it is impossible to remove. So, if you make a mistake, it is likely you will have to cutoff the existing tape and start over.
Show/hide tableIllustration 2 g06154946 - Insert folded tape between the supply and return line of the fuel manifold.
Show/hide table
Illustration 3 g06154948 Show/hide tableIllustration 4 g06154951 - Start folding the tape over the mating block on both sides.
Show/hide table
Illustration 5 g06154962 - Cut
254 mm (10 inch) long piece and start wrapping it around the two fuel lines with the edge of the tape against the mating block.Show/hide tableIllustration 6 g06154970 Show/hide tableIllustration 7 g06154980 - Continue to wrap tape around the fuel lines as shown.
Show/hide table
Illustration 8 g06154989 - Start pinching the tape together. You will want to make sure that the tape is not on the jumper tube weld block.
Show/hide table
Illustration 9 g06155003 - Cut a
406.4 mm (16 inch) long piece and fold127 mm (5 inch) of end long ways. Then, place it between the fuel lines again and wrap around the mating block.Show/hide tableIllustration 10 g06155005 - Insert the pinched end of the tape between the fuel rails again.
Show/hide table
Illustration 11 g06155009 - Push down the folded end on the backside of the fuel rail.
Show/hide table
Illustration 12 g06155014 - Wrap the opposite end of the tape around the fuel regulator.
Show/hide table
Illustration 13 g06155016 - Fold the other end.
Show/hide table
Illustration 14 g06155019 - Insert the folded end through the fuel rail and push down.
Show/hide table
Illustration 15 g06155023 - Push down all remaining loose tape.
Show/hide table
Illustration 1 | g06154912 |
Caterpillar Information System:
C7.1 Engines and Generator Sets Sensor Signal (Analog, Active) - Test
C7.1 Engines and Generator Sets Sensor Calibration Required - Test
New Engine Software for Certain C4.4 Generator Sets {108F, 1920} New Engine Software for Certain C4.4 Generator Sets {108F, 1920}
C7.1 Engines and Generator Sets Relay - Test - Fuel Transfer Pump Relay
C7.1 Engines and Generator Sets Power Take-Off - Test
Diesel Exhaust Fluid Quality Sensor Updates on C9.3 - C18 Tier 4 Final Engines {108U, 1920} Diesel Exhaust Fluid Quality Sensor Updates on C9.3 - C18 Tier 4 Final Engines {108U, 1920}
Procedure for Proper Sealing of the Swing Drive and Final Drive on All Excavators {4050} Procedure for Proper Sealing of the Swing Drive and Final Drive on All Excavators {4050}
3512E and 3516E Marine Engines Valve Mechanism Cover Base - Remove and Install
3512E and 3516E Marine Engines Cylinder Head - Remove
Base Cover Assembly Gasket on Certain C7.1 Engines {1107, 7555} Base Cover Assembly Gasket on Certain C7.1 Engines {1107, 7555}
New Cylinder Head Components Are Now Available for Certain 3508 Generator Set Engines {1100, 1101} New Cylinder Head Components Are Now Available for Certain 3508 Generator Set Engines {1100, 1101}
The 490-0654 Bellows Assembly May Be Built Wrong on Certain 3500C Marine Engines {1059} The 490-0654 Bellows Assembly May Be Built Wrong on Certain 3500C Marine Engines {1059}
New Plate Assemblies Are Now Used on Certain Cat® Engines {1379} New Plate Assemblies Are Now Used on Certain Cat® Engines {1379}
C32 Marine Auxiliary Engine On-Board Replacement Parts
C7.1 Engines and Generator Sets Sensor Signal (Analog, Passive) - Test
C7.1 Engines and Generator Sets Sensor Supply - Test
CN1566, CN2086, CN2586, CN3086, CN3586, CN4086 and CN5086 Electric Motors Space Heater - Inspect/Replace
C32 Marine Auxiliary Engine Customer Assistance
An Improved Water Lines Group Is Now Used on Certain C175-16 Locomotive Engines {1380} An Improved Water Lines Group Is Now Used on Certain C175-16 Locomotive Engines {1380}
C7.1 Engines and Generator Sets Shutdown (Ground Level) - Test
C7.1 Engines and Generator Sets Solenoid Valve - Test
G3516 Petroleum Engine Plate Locations and Film Locations
New Software Is Now Used for Certain 3412 Electric Power Application Engines {1920} New Software Is Now Used for Certain 3412 Electric Power Application Engines {1920}
C4.4 Generator Sets Voltage Regulators