Relief Valve (Transmission Hydraulic Control) - Remove and Install
Start By:
- Remove the power train guard.
- Disconnect harness assembly (1) and cut the cable straps.
- Remove bolts (3) and remove relief valve (2).
Show/hide table
Illustration 2 g06072841 - Remove O-ring seal (6).
Show/hide table
Illustration 3 g06072863 - Remove caps (5), fittings (6) and O-ring seals (7) from relief valve (2).
Show/hide table
Illustration 4 g06072868 - Remove nut (8) and coil (9) from relief valve (2).
Show/hide table
Illustration 5 g06072876 - Remove cartridge (10), O-ring seal (11), back-up ring (12), O-ring seal (13), O-ring seal (14), and back-up ring (15) from relief valve (2).
Show/hide table
Illustration 1 | g06072830 |
Note: The transmission hydraulic control relief valve is located on the right side of the transmission housing.
- Install relief valve (2) in the reverse order of the removal procedure.
- Tighten cartridge (10) to a torque
100 ± 10 N·m (74 ± 7 lb ft) - Tighten nut (8) to a torque of
8 ± 1 N·m (70 ± 9 lb in) - Tighten bolts (3) to a torque of
30 ± 4 N·m (22 ± 3 lb ft) .
- Tighten cartridge (10) to a torque
Caterpillar Information System:
A New Expansion Tank Assembly Is Now Used On Certain 3516B Marine Engines {1354} A New Expansion Tank Assembly Is Now Used On Certain 3516B Marine Engines {1354}
3512E Engines Atmospheric Pressure Sensor - Remove and Install
3512E HD Petroleum Engine Engine Rating Definitions
3512E Land Electric Drive Fuel Filter Differential Pressure - Check
Installation of Cold Climate Kit for C2.2 Engines {1071, 1090} Installation of Cold Climate Kit for C2.2 Engines {1071, 1090}
797F and 797F XQ Off-Highway Truck TA2 Technical Inspection {0372, 0374, 1000, 7000, 753T, 7565} 797F and 797F XQ Off-Highway Truck TA2 Technical Inspection {0372, 0374, 1000, 7000, 753T, 7565}
TR35 Locomotive Transmission Transmission Oil Filter Base - Remove and Install
3512E HD Petroleum Engine Engine Oil Sample - Obtain
3512E HD Petroleum Engine Coolant Sample (Level 2) - Obtain
G3512 Generator Set Engines Electronic Control System Parameters - Configuration Parameters
3512E Land Electric Drive Coolant Sample (Level 1) - Obtain
TR35 Locomotive Transmission Transmission Oil Pump - Remove and Install
TR35 Locomotive Transmission Modulating Valve (Transmission Clutch) - Remove and Install
C12.9 Marine Engines Engine Oil Pan - Remove and Install
TR35 Railway Transmission Calibrations
C12.9 Marine Engines Engine Oil Pump - Remove and Install
C175 Tier 4 Final Engines for Off-Highway Trucks Data Link - Test
C12.9 Marine Engines Exhaust Manifold - Remove and Install
TR35 Locomotive Transmission Output Transfer Gears - Disassemble
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Operator Controls (Auxiliary Hydraulic System)
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Location of Components (Auxiliary Hydraulic System)
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Electrical Schematic (Auxiliary Hydraulic System)
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Hydraulic Schematic (Auxiliary Hydraulic System)
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Hydraulic Cylinder