Crankshaft Rear Seal - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1U-7600 | Slide Hammer Puller Gp | 1 |
B | 1U-8145 | Drill Bit | 1 |
C | 456-7986 | Installer (Rear Crank Seal) | 1 |
Start By:
- Remove flywheel.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (B) to drill three evenly spaced holes in crankshaft rear seal (1).
- Alternate between the drilled holes and use Tooling (A) to remove crankshaft rear seal (1).
Show/hide table
Illustration 1 | g06067725 |
Note: Use caution when drilling near the crankshaft.
- Use Tooling (C) to install crankshaft rear seal (1).
Show/hide table
Illustration 2 | g06067898 |
Note: The crankshaft seal is a dry installation.
Caterpillar Information System:
3512E Engines Turbocharger Inlet Temperature Sensor - Remove and Install
New Cylinder Head Gasket on Certain C3.4 Engines {1100, 1103, 1104, 1105, 1108, 1109, 1115, 1117, 1121, 1124, 1125} New Cylinder Head Gasket on Certain C3.4 Engines {1100, 1103, 1104, 1105, 1108, 1109, 1115, 1117, 1121, 1124, 1125}
C4.4 Generator Sets Turbocharger - Inspect
C4.4 Generator Sets Air Inlet and Exhaust System
Selective Catalytic Reduction Retrofit Aftertreatment Diagnostic Trouble Codes
Selective Catalytic Reduction Retrofit Aftertreatment System Overview
Selective Catalytic Reduction Retrofit Aftertreatment Sensor Signal (Analog, Active) - Test
Selective Catalytic Reduction Retrofit Aftertreatment DEF Pump Motor - Test
Selective Catalytic Reduction Retrofit Aftertreatment Data Link - Test
Selective Catalytic Reduction Retrofit Aftertreatment SCR Catalyst Inlet Pressure Is Low
Selective Catalytic Reduction Retrofit Aftertreatment SCR Catalyst Inlet Pressure Is High
Selective Catalytic Reduction Retrofit Aftertreatment NOx Conversion Is Low
Selective Catalytic Reduction Retrofit Aftertreatment Event Codes
TR35 Locomotive Transmission Relief Valve (Torque Converter Outlet) - Remove and Install
Diesel Exhaust Fluid (DEF) Injector Are Failing on Certain C9.3-C18 Machine and Commercial Engines {108I} Diesel Exhaust Fluid (DEF) Injector Are Failing on Certain C9.3-C18 Machine and Commercial Engines {108I}
3512E Engines Turbocharger Outlet Pressure Sensor - Remove and Install
New Turbochargers Are Now Used on Certain 3516 and C175-16 Locomotive and Marine Engines {1052} New Turbochargers Are Now Used on Certain 3516 and C175-16 Locomotive and Marine Engines {1052}
320 GC, 320 and 323 Excavator Battery or Battery Cable - Inspect/Replace
3500E Marine Engines Engine Air Cleaner Element (Single Element) - Inspect/Replace
3512E Engines Pressure Sensor (Engine Coolant) - Remove and Install
G3512 Generator Set Engines Ignition Secondary - Test
3512E Engines Speed Sensor (Turbocharger) - Remove and Install
3512E Tier 4 Final Engines for Land Electric Drilling Coolant Pressure Is Incorrect
New Severe Service DEF Manifold Filter Option Available for Tier 4 Final C9.3-C18 Engines {108K, 3206} New Severe Service DEF Manifold Filter Option Available for Tier 4 Final C9.3-C18 Engines {108K, 3206}