Stick
Show/hide table
| |
| Illustration 1 | g06054878 |
|
Typical example | |
Show/hide table
| Specification for 357-5685 Hoe Stick Gp (1), 357-5688 Hoe Stick Gp (2), 461-5965 Hoe Stick Gp (1) , 487-2402 Hoe Stick Gp (2), 498-1233 Hoe Stick Gp (2) and 498-1237 Hoe Stick Gp (2) | |||
|---|---|---|---|
| Item | Qty | Part | Specification Description |
| All bores must be free of paint. Use 5P-0960 Grease Cartridge in order to coat all bores for the pins, the bucket, and the cylinder pin bores. | |||
| 1 | - | - | Assemble the stick cylinder so that the grease zerk is directed, as shown. (3) |
| 2 | 1 | 4I-4811 Pin As | Diameter is |
| 3 | 1 | 4I-4809 Pin As | Diameter is |
| 4 | 2 | 166-1495 Lip Type Seal | Lubricate the sealing lip lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install lip type seals so that the lip type seals do not extend beyond the face of the boss. |
| 5 | 2 | 235-7679 Lip Type Seal | Lubricate the sealing lip lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install lip type seals so that the lip type seals do not extend beyond the face of the boss. |
| 6 | 2 | 166-1494 Lip Type Seal | Lubricate the sealing lip lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install lip type seals so that the lip type seals do not extend beyond the face of the boss. |
| 7 | 2 | 357-5709 Bushing (4) | Bore before assembly is Installation depth is |
| 8 | 2 | 229-1096 Bushing (4) | Bore before assembly is Installation depth is |
| 9 | 2 | 240-2913 Bushing (4) | Bore before assembly is Installation depth is |
Show/hide table
| (1) | Stick length is |
| (2) | Stick length is |
| (3) | For 357-5688, 487-2402, 498-1233 and 498-1237. |
| (4) | Install the bushing in the bore so that identification faces the out side. |
Caterpillar Information System:
C9.3 Tier 4 Final Engines Electric Starting Motor
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Valve Stem Projection - Measure/Record
C9.3 Tier 4 Final Engines Electric Starting Motor
C13, C15, and C18 Tier 4 Final Engines Variable Valve Actuator
C12.9 Marine Engines Camshaft Gear - Remove and Install
G3512 Generator Set Spark Plugs - Inspect/Adjust/Replace - Spark Plugs with Adjustable Electrode Gaps
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Rotating Rectifier - Check
C13, C15, and C18 Tier 4 Final Engines Exhaust Cooler (NRS)
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Nitrogen Oxide Sensor - Replace
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Jacket Water Heater - Check
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Generator Load - Check
C7.1 Engines and Generator Sets Engine Monitoring System
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Configuration Parameters
G3512 Generator Set Fluid Recommendations
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Circuit Breakers - Reset
3516C Generator Set Engines Exhaust Elbow - Remove and Install
3512E Engines Vibration Damper - Remove and Install
New Engine Software Is Now Used For Certain G3520 Generator Sets {4490} New Engine Software Is Now Used For Certain G3520 Generator Sets {4490}
Discussion of Aftercooler Maintenance and Replacement Intervals Are Available for Certain Marine Engines Equipped With Sea Water Aftercooling {1063} Discussion of Aftercooler Maintenance and Replacement Intervals Are Available for Certain Marine Engines Equipped With Sea Water Aftercooling {1063}
G3512 Generator Set Engines Solenoid Valve - Test
3512E Tier 4 Final Engines for Land Electric Drilling Sensor Signal (PWM) - Test
C13, C15, and C18 Tier 4 Final Engines Jacket Water Heater
C13, C15, and C18 Tier 4 Final Engines Fumes Disposal Group
C13, C15, and C18 Tier 4 Final Engines Flywheel Housing Cover