Engine Oil Pan - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Loctite Blue RTV Silicone | - |
B | 1Y-3904 | Adhesive | - |
- Drain the engine oil. Refer to the Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct draining and filling procedures.
- Remove the O-ring seal from the drain plugs.
Show/hide table
Illustration 1 g06050708 - The weight of oil pan assembly (2) is approximately
46 kg (101 lb) . - Remove bolts (1) and use a suitable lifting device to remove oil pan (2).
Show/hide table
Illustration 2 g06051056 - Remove bolts (4) and plate (3).
Show/hide table
Illustration 3 g06051152 - Remove gasket (5) from the oil pan.
- Install a new gasket (5).
Show/hide table
Illustration 5 g06051056 - Install plate (3) and bolts (4).
Show/hide table
Illustration 6 g06051306 - Apply Tooling (A) to locations shown in Illustration 6.
Show/hide table
Illustration 7 g06050708 - The weight of oil pan assembly (2) is approximately
46 kg (101 lb) . - Use a suitable lifting device to install oil pan (2) and bolts (1).
Show/hide table
Illustration 8 g02463392 Torque sequences for bolts (1). - Tighten bolts (1) to a torque of
40 ± 5 N·m (30 ± 4 lb ft) according to Sequence (A) in Illustration 8. - Retighten bolts (1) to a torque of
47 ± 5 N·m (35 ± 4 lb ft) according to Sequence (B) in Illustration 8. - Fill the engine oil. Refer to the Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct draining and filling procedures.
Show/hide table
Illustration 4 | g06051152 |
Caterpillar Information System:
C18 Generator Set Engines Camshaft Bearings - Remove and Install
3512E Tier 4 Final Engines for Land Electric Drilling Cooling Fan Speed - Test
C9.3 Marine Propulsion Engine Overhaul (Major)
C18 Generator Set Engines Camshaft Gear - Remove and Install
3512E Tier 4 Final Engines for Land Electric Drilling Exhaust System Contains Oil
Piston Height Check Procedure for C9.3 through C18 Tier 4 Engines {1000, 108C, 1214} Piston Height Check Procedure for C9.3 through C18 Tier 4 Engines {1000, 108C, 1214}
System Check after an NOx Reduction System (NRS) Cooler Failure for C9.3 through C18 Tier 4 Engines {1000, 1075, 108C, 108F} System Check after an NOx Reduction System (NRS) Cooler Failure for C9.3 through C18 Tier 4 Engines {1000, 1075, 108C, 108F}
C18 Generator Set Engines Camshaft - Remove and Install
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Fan Speed (Ventilation) - Test
C18 Generator Set Engines Cylinder Head - Remove and Install
C18 Generator Set Engines Rocker Arm - Assemble
TA22 OEM Construction Transmission Lubricant Viscosities
C9.3 Marine Auxiliary Engines Refill Capacities
C12.9 Marine Engines Aftercooler - Remove and Install - Low-Pressure
Installation Procedure for Cat® Product Link Generation (PLG6x1) {7606, 7610, 7620} Installation Procedure for Cat® Product Link Generation (PLG6x1) {7606, 7610, 7620}
C12.9 Marine Engines Expansion Tank - Remove and Install
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Fan Pump - Test and Adjust
C7.1 Marine Propulsion Engine Model View Illustrations
Troubleshooting Guide for the Rotary Position Sensor for Cat® Grade Control on Certain Series E and Series F Excavators {5736} Troubleshooting Guide for the Rotary Position Sensor for Cat® Grade Control on Certain Series E and Series F Excavators {5736}
3512E Petroleum Engines General Information (Fuel System)
C13, C15, and C18 Tier 4 Final Engines Diesel Exhaust Fluid Tank
New Exhaust Gaskets Are Used on Certain 3500 Engines {1059} New Exhaust Gaskets Are Used on Certain 3500 Engines {1059}
C18 Generator Set Engines Cylinder Liner - Remove and Install
C15 Generator Sets Maintenance Interval Schedule - Emergency Standby Power