Gear Group (Rear) - Remove and Install - Flywheel Housing
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 439-3939 | Link Bracket | 2 |
Start By:
- Remove the electric starting motor.
- Remove the flywheel.
- Support the engine.
Show/hide table
Illustration 1 g06002548 - Remove bolts (2) and rear crankshaft seal (1).
Show/hide table
Illustration 2 g06002556 - Remove bolts (4) and the washers. Remove cover (3) and the seal.
Show/hide table
Illustration 3 g06002558 - Remove gear (7), bolts (6), and gear (5).
Show/hide table
Illustration 4 g06002564 - Remove O-ring seal (8) from gear (7).
Show/hide table
Illustration 5 g06002568 - Attach Tooling (A) and a suitable lifting device to flywheel housing (9). The weight of flywheel housing (9) is approximately
135 kg (297 lb) . - Remove bolts (10) and flywheel housing (9).
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 439-3939 | Link Bracket | 2 |
B | - | Loctite Anaerobic Flexible Gasket Maker | - |
C | 095-0706 | Bolt | 2 |
- Apply Tooling (B) to the face of the cylinder block.
Show/hide table
Illustration 6 g06002568 - Attach Tooling (A) and a suitable lifting device to flywheel housing (9). The weight of flywheel housing (9) is approximately
135 kg (297 lb) . Position flywheel housing (9) on the rear of the cylinder block. - Install the washers and bolts (10).
Show/hide table
Illustration 7 g06002564 - Install O-ring seal (8) onto gear (7).
Show/hide table
Illustration 8 g06002578 - Install gear (5) and bolts (6).
Note: Tooling (C) is for supporting gear (7) during the installation of the cover and the rear crankshaft seal.
Note: The bolt holes in gear (7) are not symmetrical. When installing Tooling (C), check the rest of the bolts holes in gear (7) are aligned with the holes in the crankshaft.
- Install gear (7) and Tooling (C).
Show/hide table
Illustration 9 g06002581 - Install cover (3), the seal, bolts (4), and the washers.
Show/hide table
Illustration 10 g06002592 - Install rear crankshaft seal (1) and bolts (2).
- Remove Tooling (C).
End By:
- Install the flywheel.
- Install the electric starting motor.
Caterpillar Information System:
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Engine Oil and Filter - Change
C2.2 Engines for Caterpillar Built Machines Air in Fuel - Test
C1.7 and C2.2 Industrial Engines Maintenance Interval Schedule
G3508J, G3516J, and G3520J Engines Turbocharger - Remove
C1.7 and C2.2 Industrial Engines Engine Oil and Filter - Change
C1.7 and C2.2 Industrial Engines Engine Crankcase Breather Element - Replace
C1.7 and C2.2 Industrial Engines Engine Electronics
3516E Generator Set Engines Gear Group (Rear)
3516E Generator Set Engines Fuel Priming Pump
C1.7 and C2.2 Industrial Engines Engine Air Cleaner Element - Replace
C1.7 and C2.2 Industrial Engines Emissions Certification Film
3516E Generator Set Engines Cylinder Head
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Generator - Dry
An Improved Final Drive Ring Gear Retainer is Now Used on Certain 777 Off-Highway Trucks {4008, 4050} An Improved Final Drive Ring Gear Retainer is Now Used on Certain 777 Off-Highway Trucks {4008, 4050}
C1.7 and C2.2 Industrial Engines Monitoring System
C1.7 and C2.2 Industrial Engines Turbocharger - Inspect
C1.7 and C2.2 Industrial Engines Walk-Around Inspection
C1.7 and C2.2 Industrial Engines Engine Design
C1.7 and C2.2 Industrial Engines Welding on Engines with Electronic Controls
C1.7 and C2.2 Industrial Engines Fluid Recommendations
G3508J, G3516J, and G3520J Engines Turbocharger - Install
C18 Generator Set Engines Turbocharger - Remove and Install
C1.7 and C2.2 Industrial Engines Gauges and Indicators
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215} NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}