Valve Cover Base - Remove and Install
开始:
- 拆下阀室盖。
- 卸下固定摇臂组件 (2) 的两个螺栓 (1)。 卸下摇臂组件。 卸下进气阀的中心推杆。 在摇臂组件上作识别标记,以便可以将组件安装至恰当位置。
- 在推杆 (4) 上作识别标记,以便可以将推杆 (4) 安装至恰当位置。 卸下推杆 (4)。
- 卸下阀桥 (3)。 确定各个阀桥的位置,以便可以将阀桥 (3) 安装至恰当位置。
- 检查每个阀桥的孔是否磨损。 确保阀桥内的润滑油道通畅。
- 检查阀桥定位销 (5) 是否磨损。 如果必须卸下阀桥定位销,请参阅本手册中拆解和装配, "缸盖 - 拆解"章节。
- 检查摇臂轴支架的销 (6)(未显示)。 定位销必须在支架上方
8 ± 1 mm (0.315 ± 0.039 inch) 处。
Show/hide table
图 1 | g03831418 |
注: 图中编号 (7) 为摇臂的调整螺钉。
Caterpillar Information System:
Tier 4 Final Engines for Wheel Tractor-Scrapers Data Link - Test
C18 Industrial Engine Fuel Pressure Is Low
C9.3 Marine Auxiliary and Generator Set Engine Sensor Signal (Analog, Passive) - Test
C11, C13, C15, and C18 Industrial Engines Cooling Fan Control - Test
C175-16 Engine for Off-Highway Trucks Engine Oil Level Sensor
C2.2 Engines For Caterpillar Built Machines Data Link Configuration Status - Test
Procedure to Upgrade EMCP 1, EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.2 {4490, 7451} Procedure to Upgrade EMCP 1, EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.2 {4490, 7451}
C7 and C9 Industrial Engines Diagnostic Trouble Codes
C7 and C9 Industrial Engines Diagnostic Trouble Code Cross Reference
G3304B and G3306B Engines Exhaust Manifold - Install
G3304B and G3306B Engines Exhaust Manifold - Remove
G3304B and G3306B Engines Spark Plug Adapter - Remove and Install
C11, C13, C15, and C18 Industrial Engines Exhaust Balance Valve - Test
G3612 and G3616 Engines Rocker Arm - Remove
3500E EPA Tier 4 Final and IMO-II/III Switchable Marine Engines Aftertreatment SCR System Dosing - Test
C11, C13, C15, and C18 Industrial Engines NOx Reduction System (NRS) - Test
G3612 and G3616 Engines Rocker Arm - Install
C18 Industrial Engine Sensor Supply - Test
G3612 and G3616 Engines Gas Admission Valve - Remove
C11, C13, C15, and C18 Industrial Engines Solenoid Valve - Test
G3612 and G3616 Engines Gas Admission Valve - Install
2015/05/15 New Generators on Certain C2.2 Marine Generator Sets {4450}
G3612 and G3616 Engines Valve Mechanism - Remove
C2.2 Engines For Caterpillar Built Machines Injector Solenoid - Test