Rocker Arm - Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 检查摇臂中的轴承是否磨损。 每个摇臂轴承的内径为
70.000 ± 0.015 mm (2.7559 ± 0.0006 inch) 。 - 检查轴是否磨损。 摇臂轴的外径为
69.900 ± 0.015 mm (2.7520 ± 0.0006 inch) 。 - 确保摇臂和摇臂轴的润滑油道通畅。
- 将新的 O 形密封圈安装在摇臂上。 在 O 形密封圈上涂上清洁的机油。
- 将按钮 ( 1 )安装在摇臂上。
- 在装配时,将清洁的发动机机油涂在摇臂轴 (5 )和摇臂轴承上。
- 将下列摇臂安装到摇臂轴上: (8)、 (7) 和 (6)。
- 将盘 (2 )放置在摇臂轴末端的合适位置。 安装将盘固定到位的两个螺栓 ( 3)。
- 将两个螺栓 ( 4) 和垫圈安装在摇臂轴内。
Show/hide table
图 1 | g03831463 |
Show/hide table
图 2 | g00563304 |
结束:
- 安装阀室盖。
Caterpillar Information System:
C11, C13, C15, and C18 Industrial Engines NOx Reduction System (NRS) - Test
3500E EPA Tier 4 Final and IMO-II/III Switchable Marine Engines Aftertreatment SCR System Dosing - Test
G3612 and G3616 Engines Rocker Arm - Remove
C11, C13, C15, and C18 Industrial Engines Exhaust Balance Valve - Test
G3612 and G3616 Engines Valve Cover Base - Remove and Install
Tier 4 Final Engines for Wheel Tractor-Scrapers Data Link - Test
C18 Industrial Engine Fuel Pressure Is Low
C9.3 Marine Auxiliary and Generator Set Engine Sensor Signal (Analog, Passive) - Test
C11, C13, C15, and C18 Industrial Engines Cooling Fan Control - Test
C175-16 Engine for Off-Highway Trucks Engine Oil Level Sensor
C2.2 Engines For Caterpillar Built Machines Data Link Configuration Status - Test
Procedure to Upgrade EMCP 1, EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.2 {4490, 7451} Procedure to Upgrade EMCP 1, EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.2 {4490, 7451}
C18 Industrial Engine Sensor Supply - Test
G3612 and G3616 Engines Gas Admission Valve - Remove
C11, C13, C15, and C18 Industrial Engines Solenoid Valve - Test
G3612 and G3616 Engines Gas Admission Valve - Install
2015/05/15 New Generators on Certain C2.2 Marine Generator Sets {4450}
G3612 and G3616 Engines Valve Mechanism - Remove
C2.2 Engines For Caterpillar Built Machines Injector Solenoid - Test
C11, C13, C15, and C18 Industrial Engines Variable Valve Actuator Response - Test
C8.7 Marine Engine Camshaft - Remove and Install
C9.3 Marine Engine Exhaust Elbow - Remove and Install
Caterpillar® C N Electric Motors Installation and Removal Guide. {5927} Caterpillar® C N Electric Motors Installation and Removal Guide. {5927}
C9.3 Marine Engine Exhaust Elbow - Remove and Install