Crankcase Fumes Disposal Tube Has Oil Draining
通气孔的冷凝排放正常。 排放物通常是洁净的但也可能含有烟尘。 虽然排放物可以含有油蒸汽,但任何液态油均必须限制为每小时最多 0.5 g (0.02 oz)。 如果油排放量超过 0.5 g (0.02 oz),则必须进行检查。
可能原因
- 通气孔滤清器
- 发动机机油油位
- 单向阀
- 窜气过多
建议的措施
注: 下面以概率的先后顺序列出了这些步骤。 依次完成这些步骤。
Show/hide table
图 1 | g03758596 |
典型通气孔滤筒 (1) 通气孔滤筒盖 (2) 滤清器滤芯 (2) 通气孔滤筒 |
Show/hide table
故障诊断与排除测试步骤     | 数值     | 结果     |
---|---|---|
1. 通气孔滤清器 A. 检查并确认滤清器滤芯 (2) 正确安装且滤芯没有损坏。 B. 检查通气孔滤筒 (3) 有无受阻或堵塞。 注释:如果在使用寿命结束前新滤清器滤芯堵塞,则表明发动机存在故障。 注释:在寒冷天气下,通气孔滤筒的出口会结冰。     |
滤清器     |
结果:滤清器滤芯 (1) 安装不当或滤芯损坏。 修理:正确安装滤清器滤芯或更换滤清器滤芯。 结果:通气孔滤筒受阻或堵塞。 修理:清洁通气孔滤筒内部。 结果:通气孔干净且运行正常。 转至测试步骤 2。     |
2. 发动机机油油位 A. 检查发动机中的机油油位。     |
机油油位     |
结果:发动机机油油位高。 修理:检查机油是否受燃油或冷却液污染。 请参阅故障诊断与排除, "机油含有燃油"或故障诊断与排除, "机油含有冷却液"。 如果发动机机油没有受到污染,则清除多余的机油。 结果:发动机机油油位正确。 转至测试步骤 3。     |
Show/hide table
图 2 | g03758618 |
(4) 通气孔排放软管 (5) 单向阀 |
Show/hide table
故障诊断与排除测试步骤     | 数值     | 结果     |
---|---|---|
3. 单向阀 A. 将通气孔排放软管 (4) 从单向阀 (5) 上断开,然后将单向阀从发动机上拆下。 请参阅拆解和组装, "曲轴箱呼吸器 - 拆卸"。 B. 使用适当的清洗液冲洗单向阀。 C. 连接单向阀的低压供气通气孔排放软管侧。 空气必须自由通过阀。 D. 连接单向阀的低压供气曲轴箱侧。 阀必须堵塞气流。     |
单向阀     |
结果:单向阀运行不正常。 修理:安装更换用阀。 请参阅拆解和组装, "曲轴箱呼吸器 - 安装"。 结果:单向阀运行正常。 继续测试步骤 4。     |
4. 窜气过多 注释:窜气过多会增加经过通气孔系统的烟气量,可导致烟气排放管排出机油。 A. 检查发动机的窜气是否过多。     |
窜气     |
结果:窜气过多。 修理:更换通气孔滤清器。 调查窜气过多的原因。 请参阅故障诊断与排除, "机油消耗过多"。 结果:窜气不多。 请联系代理商解决方案网络 (DSN)。     |
Caterpillar Information System:
C8.7 Marine Engines Camshaft
C9 Generator Set Maintenance Interval Schedule - Standby
2014/11/24 "Maintenance Mode" in Product Link is Used to Prevent Codes From Being Transmitted When Performing Service to a Machine or Engine {7606}
C9 Generator Set Maintenance Interval Schedule - Prime Power
New Hybrid Hydraulic Hoses Are Available for TH55-E70 and TH55-E90 Petroleum Transmissions {3016, 5057} New Hybrid Hydraulic Hoses Are Available for TH55-E70 and TH55-E90 Petroleum Transmissions {3016, 5057}
2014/12/12 A New Torque Value for the Flywheel Group Is Used on Certain C18 Engines {1156}
XQ570 Rental Generator Set Selective Catalytic Reduction Warning System
C13 Generator Set Engine Diesel Particulate Filter - Remove and Install
3512E Land Electric Drive Starting Motor - Inspect
3512E Land Electric Drive Overhaul (Top End)
3512E Land Electric Drive Maintenance Recommendations
C4.4 and C6.6 Engines Cooling Fan Is Always ON
C3.4B Industrial Engine Coolant Level - Check
2015/09/28 A New Clamp Assembly Is Used on Certain 3516 Engines {1071, 7231}
2014/12/05 Bolted Flange Exhaust Is Now Used on G3520E Engines {1059}
2015/01/30 New Bolts Are Available For Certain C175-16 Locomotive Engine Trunnion Mounts {1153, 1154}
C4.4 and C7.1 Engines Cylinder Is Noisy
C13 Generator Set Engine Inlet Module (Catalyst) - Remove and Install
2014/11/26 New Alternator for Certain C4.4 and C6.6 Engines {1405}
2014/12/05 New Recommendations for Plumbing the Gear Oil Cooler on Certain C32 Marine Engines {3320}
C13 Generator Set Engine Air Inlet Elbow - Remove and Install
3512C and 3516C Engines Maintenance Interval Schedule - Prime Power
2014/12/24 Revision to "Reports and Messages Not Available" Troubleshooting Procedure for Cat® Products with Cat® Product Link 121/321 {7606}
C7.1 Engines DEF Control Module Temperature Is High