Camshaft
Show/hide table
Illustration 1 | g03758138 |
Show/hide table
Illustration 2 | g03761879 |
Show/hide table
Specification for 431-4117 Camshaft     | |||
---|---|---|---|
Item     | Qty     | Part     | Specification Description     |
1     | 5     | 438-0901 Bolts     | Tighten to 20 ± 2 N·m (177 ± 18 lb in) in the following sequence 1-2-3-4-5. Tighten bolts again to 20 ± 2 N·m (177 ± 18 lb in) the following sequence 1-3-5-2-4     |
2     | 4     | 438-0903 Bolts     | Tighten to 25 ± 1.25 N·m (220 ± 11 b in ) Turn the bolts an addition 45 ± 5 degrees     |
3     | 3     | 431-4124 Sealing Plate     | Tighten to 23 ± 2 N·m (204 ± 18 lb in)     |
4     | 3     | 438-0914 Bolt     | Tighten to 23 ± 2 N·m (204 ± 18 lb in)     |
Show/hide table
Illustration 3 | g03331247 |
Show/hide table
Item     | Qty     | Part     | Specification Description     |
-     | -     | -     | Use the following procedure in order to determine the actual camshaft lobe lift: 1. Measure camshaft lobe height (C). 2. Measure base circle (D). 3. Subtract the base circle (D) from the camshaft lobe height (C). The difference is the actual camshaft lobe lift.     |
B     | -     | -     | Specified camshaft lobe lift for: Inlet lobe is 7.4034 mm (0.2915 inch). Exhaust lobe is 8.2108 mm (0.3233 inch).     |
Caterpillar Information System:
C9 Generator Set Maintenance Interval Schedule - Standby
2014/11/24 "Maintenance Mode" in Product Link is Used to Prevent Codes From Being Transmitted When Performing Service to a Machine or Engine {7606}
C9 Generator Set Maintenance Interval Schedule - Prime Power
New Hybrid Hydraulic Hoses Are Available for TH55-E70 and TH55-E90 Petroleum Transmissions {3016, 5057} New Hybrid Hydraulic Hoses Are Available for TH55-E70 and TH55-E90 Petroleum Transmissions {3016, 5057}
2014/12/12 A New Torque Value for the Flywheel Group Is Used on Certain C18 Engines {1156}
XQ570 Rental Generator Set Selective Catalytic Reduction Warning System
C13 Generator Set Engine Diesel Particulate Filter - Remove and Install
3512E Land Electric Drive Starting Motor - Inspect
3512E Land Electric Drive Overhaul (Top End)
3512E Land Electric Drive Maintenance Recommendations
C4.4 and C6.6 Engines Cooling Fan Is Always ON
3512E Land Electric Drive Engine Oil - Change
C4.4 Engines Crankcase Fumes Disposal Tube Has Oil Draining
C3.4B Industrial Engine Coolant Level - Check
2015/09/28 A New Clamp Assembly Is Used on Certain 3516 Engines {1071, 7231}
2014/12/05 Bolted Flange Exhaust Is Now Used on G3520E Engines {1059}
2015/01/30 New Bolts Are Available For Certain C175-16 Locomotive Engine Trunnion Mounts {1153, 1154}
C4.4 and C7.1 Engines Cylinder Is Noisy
C13 Generator Set Engine Inlet Module (Catalyst) - Remove and Install
2014/11/26 New Alternator for Certain C4.4 and C6.6 Engines {1405}
2014/12/05 New Recommendations for Plumbing the Gear Oil Cooler on Certain C32 Marine Engines {3320}
C13 Generator Set Engine Air Inlet Elbow - Remove and Install
3512C and 3516C Engines Maintenance Interval Schedule - Prime Power
2014/12/24 Revision to "Reports and Messages Not Available" Troubleshooting Procedure for Cat® Products with Cat® Product Link 121/321 {7606}