Engine Stalls at Low RPM
可能原因
- 诊断代码
- 附属设备
- 燃油系统检查
- 低压缩(气缸压力)
- 电子单体喷油器
建议的措施
注: 下面以概率的先后顺序列出了这些步骤。 依次完成这些步骤。
Show/hide table
故障诊断与排除测试步骤     | 数值     | 结果     |
---|---|---|
1. 诊断代码 A. 建立电子维修工具和电子控制模块 (ECM) 之间的通信。 如有必要,请参阅故障诊断与排除, "电子维修工具"。 B. 检查有无任何激活的或记录的代码。     |
诊断代码     |
结果:代码激活或被记录。 在继续进行本程序之前,诊断并排除所有代码。 结果:代码未处于现行或记录状态。 转至测试步骤 2。     |
2. 附属设备 A. 检查所有附件设备有无可能会将过度的负载施加在发动机上的故障。     |
附件     |
结果:发动机附件正在产生过高负载。 修理或更换发动机附件。 结果:发动机附件未形成过高负载。 转至测试步骤 3。     |
3. 燃油系统检查 A. 确认燃油切断阀处于打开位置。 B. 如果温度低于 0 °C (32 °F),检查燃油有无凝固(结蜡)。 C. 检查供油管路有无阻塞。 D. 检查低压燃油管路是否正确安装。 E. 检查燃油系统中的压力 请参阅系统操作、测试和调整, "燃油系统压力 - 测试" F. 检查柴油是否受污染。 请参阅系统操作、测试和调整, "燃油质量 - 测试"。 G. 检查燃油系统内是否有空气。 请参阅系统操作、测试和调整, "燃油混入空气 - 测试"。 H. 确保燃油系统已充注。 请参阅系统操作、测试和调整, "燃油系统 - 充注"。     |
燃油系统     |
结果:燃油系统发现缺陷。 进行任何必要的修理。 结果:没有发现缺陷。 继续测试步骤 4。     |
4. 低压缩(气缸压力) A. 执行压缩测试。 请参阅系统操作、测试和调整, "压缩 - 测试"。     |
压缩压力低     |
结果:记录了一缸或多缸上的压缩压力低。 压缩压力低的可能原因如下所列: ·预热塞松动 ·活塞故障 ·活塞环故障 ·缸径磨损 ·气门磨损 ·缸盖密封垫故障 ·缸盖损坏 根据需要进行修理。 结果:未发现故障。 继续测试步骤 5。     |
5. 电子单体喷油器 A. 使用电子维修工具检查有无与燃油喷油器相关的激活的诊断代码。     |
诊断代码     |
结果:有激活的燃油喷油器诊断代码。 对激活的诊断代码进行问题诊断和解决。 请参阅故障诊断与排除, "故障诊断代码"。 结果:所有喷油器正常。 请联系代理商解决方案网络 (DSN)。     |
Caterpillar Information System:
XQC1200 and XQC1600 Power Modules Engine Speed Sensor - Remove and Install
3304B-XQ125 Rental Generator Set Engine Storage
XQC1200 and XQC1600 Power Modules Regulator (Engine Oil Level) - Remove and Install
326F Excavator Sound Information and Vibration Information
2014/08/01 A New Emergency Stop Contact Is Used On Certain C18 Marine Engines {4490, 7418, 7490}
XQC1200 and XQC1600 Power Modules Valve Mechanism Cover Base - Remove and Install
3304B-XQ125 Rental Generator Set Safety Messages
C13 and C15 On-Highway Engines Maintenance Interval Schedule - C13 and C15 On-highway Engines with Standard (Deep) Oil Pans
C13 and C15 On-Highway Engines Maintenance Interval Schedule - C13 Engines with Standard (Deep) Sumps and 500 HP Field Up-Rates or C13 Engines with Standard (Deep) Sumps and 525 hp RV Ratings or C13 Engines with Center Oil Pans
2014/07/25 New Exhaust Bellows Assemblies and Band Clamps Are Used On Certain C175 Engines {1059}
XQC1200 and XQC1600 Power Modules Rocker Shaft and Push Rod - Remove and Install
3304B-XQ125 Rental Generator Set Maintenance Interval Schedule - Standby
C3.4B Engines Engine Top Speed Is Not Obtained
C3.4B Engines Exhaust Has Excessive Black Smoke
C8.7 Marine Engine Coolant Sample (Level 1) - Obtain
XQC1200 and XQC1600 Power Modules Atmospheric Pressure Sensor - Remove and Install
C3.4B Engines Exhaust System Contains Oil
C8.7 Marine Engine Cooling System Supplemental Coolant Additive (SCA) - Test/Add
C8.7 Marine Engine Engine Air Cleaner Service Indicator - Inspect
C3.4B Engines Fuel Consumption Is Excessive
XQC1200 and XQC1600 Power Modules Engine Speed/Timing Sensor - Remove and Install
2014/08/08 Cat® Reman Has Added Alternators and Starting Motor Groups for Certain Engines and Generator Set Engines {1405, 1453}
2014/08/15 Cat® Reman Has Added Alternators and Starting Motor Groups for Certain Machine Engines {1405, 1453}
2014/08/01 Cat® Reman Now Offers Additional Engine Options for Certain C32 Industrial Engines {1000}