Pump (Power End) Connection Rod Bearings - Inspect
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 有关适于收集和盛放 Cat 产品油液的工具和用品,请参阅专门出版物, NENG2500, "Cat 代理商维修工具目录"或专门出版物, PECJ0003, "Cat 车间用品和工具目录"。 按照本地法规和要求处置所有油液。 |
检查
正常定期维护期间,密切观察机油滤清器一般会指示滚柱轴承和轴颈轴承的状况。
应每 500 小时拆下一次检视盖并检查一下轴承的状况。
连杆轴承严重磨损或损坏时,曲轴上的匹配连杆轴颈通常也将会损坏。 可能需要拆卸和修理曲轴。 拆下带连杆轴承的曲轴和相连的连杆轴承壳。 有关信息和步骤,请参阅拆解和装配手册, "十字头 - 拆卸和安装"。
更换
工作循环和维修类型可能不同。 仅基于工作小时数来评估泵的磨损可能会有困难。 连杆轴承和滚柱轴承可能需要在大约 3000 小时后进行更换。 广泛的磨损迹象通常显示为材料剥落,导致工作表面点蚀或划伤。 轴承表面的任何剥落表示须立即更换该零件。 有关信息和步骤,请参阅拆解和装配手册, "十字头 - 拆卸和安装"。
Caterpillar Information System:
Installing the ECM Software on Certain C3.4B Engines{1901, 1920} Installing the ECM Software on Certain C3.4B Engines{1901, 1920}
323F SA and 323F LN Excavator and 323F LN MHPU Machine Systems Specifications Pilot Lines
Well Service Pumps Pump (Power End) Breather - Clean
Well Service Pumps Pump (Fluid End) Mounting Bolts - Check
C8.7 Marine Engine Engine Mounts - Inspect
455-1185 Major Overhaul Foundational Kit for C18 Marine Engines{1000} 455-1185 Major Overhaul Foundational Kit for C18 Marine Engines{1000}
Well Service Pumps Pump (Fluid End) Suction Pulsation Dampener - Check
Well Service Pumps Pump (Fluid End) Discharge Flanges and Seals - Inspect
558 Forest Machine Fuel System Secondary Filter - Replace
Well Service Pumps Pump (Fluid End) Suction Manifold Seals - Replace
455-1187 Major Overhaul Foundational Kit for C18 Marine Engines{1000} 455-1187 Major Overhaul Foundational Kit for C18 Marine Engines{1000}
2015/02/20 New Front and Rear Crankshaft Seals Are Now Used on Certain 3500 and G3500 Engines {1160, 1161}
Well Service Pumps Pump (Power End) Gears - Inspect
C8.7 Marine Engines Supercharger - Inspect
2014/10/03 A New Tube Is Now Used for Certain 3512 and 3516 Marine and Petroleum Engines {1354}
C8.7 Marine Engines Cooling System - Test
455-1184 Major Overhaul Foundational Kit for C18 Marine Engines{1000} 455-1184 Major Overhaul Foundational Kit for C18 Marine Engines{1000}
3516C and C175-16 Engines Selective Catalytic Reduction DEF Tank Level Is Low
C8.7 Marine Engines Vibration Damper - Check
Inspection and Installation Procedure for C175 Exhaust Bellows {1059, 1061} Inspection and Installation Procedure for C175 Exhaust Bellows {1059, 1061}
C8.7 Marine Engines Engine Oil Pressure - Test
G3500 Engines Welding on Engines with Electronic Controls
2014/07/25 Capturing Engine Stop Messages and Idle Information on All Caterpillar Products Equipped with Product Link 522 {7606}
320D and 323D Excavators Machine System Specifications Auxiliary Hydraulic Lines