Gear Group (Front)
Show/hide table
Illustration 1 | g02659957 |
Typical example |
(1) Fuel injection pump drive gear
- Initial torque for the nut ...
18 N·m (13 lb ft)
- Final torque for the nut ...
80 N·m (59 lb ft)
- Number of teeth ... 24
(2) Idler gear
- Torque for the bolt for the idler gear ...
75 N·m (55 lb ft)
- Width of idler gear and bearing assembly ...
20.8 mm (0.81890 inch)
- Inside diameter of idler gear bearings ...
36.990 to 37.075 mm (1.45630 to 1.45964 inch)
- Outside diameter of idler gear hub ...
36.950 to 36.975 mm (1.45472 to 1.45571 inch)
- Clearance of idler gear bearing on hub ...
0.015 to 0.125 mm (0.00059 to 0.00492 inch)
- The end play of the idler gear ...
0.3 to 0.483 mm (0.01181 to 0.01902 inch)
- Number of teeth ... 31
(4) Camshaft gear
- Torque for the bolts for the camshaft gear ...
25 N·m (18 lb ft)
- Number of teeth ... 72
(5) Crankshaft gear
- Bore diameter of crankshaft gear ...
50.88 to 50.92 mm (2.00315 to 2.00472 inch)
- Outside diameter of crankshaft hub ...
50.984 to 51.000 mm (2.00724 to 2.00787 inch)
- Clearance of gear on crankshaft ...
0.06 to -0.12 mm (0.00236 to -0.00472 inch)
- Number of teeth ... 36
(6) Oil pump idler gear
- Inside diameter of oil pump idler gear bearing ...
16.012 to 16.043 mm (0.63039 to 0.63161 inch)
- Outside diameter of oil pump idler gear shaft ...
15.987 to 16.000 mm (0.62941 to 0.62992 inch)
- End play of the oil pump idler gear ...
0.05 to 0.15 mm (0.00197 to 0.00591 inch)
(7) Oil pump gear
- Inside diameter of oil pump gear bearing ...
15.932 to 15.957 mm (0.62724 to 0.62823 inch)
- Outside diameter of oil pump gear shaft ...
15.987 to 16.013 mm (0.62941 to 0.63043 inch)
- End play of the oil pump gear ...
0.05 to 0.15 mm (0.00197 to 0.00591 inch)
Backlash values
- Backlash between the fuel injection pump gear (1) and the idler gear (2) ...
0.07 to 0.17 mm (0.00276 to 0.00669 inch)
- Backlash between the idler gear (2) and the accessory drive gear (if equipped) (3) ...
0.07 to 0.17 mm (0.00276 to 0.00669 inch)
- Backlash between the idler gear (2) and the camshaft gear (4) ...
0.07 to 0.17 mm (0.00276 to 0.00669 inch)
- Backlash between the camshaft gear (4) and the crankshaft gear (5) ...
0.07 to 0.17 mm (0.00276 to 0.00669 inch)
- Backlash between the crankshaft gear (5) and the oil pump idler gear (6) ...
0.07 to 0.17 mm (0.00276 to 0.00669 inch)
- Backlash between the oil pump idler gear (6) and the oil pump gear (7) ...
0.07 to 0.17 mm (0.00276 to 0.00669 inch)
Caterpillar Information System:
C9 Generator Set Coolant (DEAC) - Change
Instructions for Use of Cat® Coolant Conditioner for Modular Core Aluminum Radiators {1350, 1350, 1352, 1353, 1395} Instructions for Use of Cat® Coolant Conditioner for Modular Core Aluminum Radiators {1350, 1350, 1352, 1353, 1395}
C8.7 Marine Engine Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
C3.4B Engines for Caterpillar Built Machines Water Temperature Regulator and Housing
C3.4B Engines for Caterpillar Built Machines Cylinder Head Valves
C3.4B Engines for Caterpillar Built Machines Lifter Group
TA2 Technical Inspection for 3512C Dynamic Gas Blending Marine Engines{0372, 1000, 753T, 7565} TA2 Technical Inspection for 3512C Dynamic Gas Blending Marine Engines{0372, 1000, 753T, 7565}
C3.4B Engines for Caterpillar Built Machines Piston and Rings
C3.4B Engines for Caterpillar Built Machines Connecting Rod
C3.4B Engines for Caterpillar Built Machines Main Bearing Journal
C4.4 Engines for Caterpillar Built Machines Electronic Control Module - Remove and Install
C3.4B Engines for Caterpillar Built Machines Connecting Rod Bearing Journal
2014/06/20 An Improved Inspection Process for Cylinder Liners Used in All 3500 Engines {1201, 1216}
2014/09/11 New Steering Line Assembly Is Now Available on Certain 621H, 623H, and 627H Wheel Tractor-Scrapers {4304, 5050}
G3306B Petroleum Generator Set Engines Engine Control Panel
G3306B Petroleum Generator Set Engines Fuel Pressure Is Low
G3306B Petroleum Generator Set Engines System Configuration Parameters
G3306B Petroleum Generator Set Engines Oxygen Level - Test
C175-16 PETROLEUM ENGINES High Pressure Fuel Rails - Remove and Install
C9 Generator Set Safety Messages
Electronic Fluid Temperature Control (ESTAT) Salvage Guideline {0374, 0599, 0700, 0701, 0708, 135V} Electronic Fluid Temperature Control (ESTAT) Salvage Guideline {0374, 0599, 0700, 0701, 0708, 135V}
XQC1200 and XQC1600 Power Modules Turbocharger - Remove and Install
C27 and C32 Generator Set Engines Fuel Priming Pump - Remove and Install
C27 and C32 Generator Set Engines Fuel Filter Base - Remove