Cylinder Head Valves
Show/hide table
Illustration 1 | g01335203 |
Typical example |
When the valve springs (1) are replaced the valve springs must be replaced in pairs.
The free length for the valve spring ...
Show/hide table
The load for the valve spring | The length of the valve spring |
|
|
|
|
Show/hide table
Illustration 2 | g01335204 |
(2) Valve face angle
- Inlet ... 30 degrees
- Exhaust ... 30 degrees
(3) Valve stem diameter
- Inlet ...
5.975 to 5.99 mm (0.23524 to 0.23583 inch) - Exhaust ...
5.975 to 5.99 mm (0.23524 to 0.23583 inch) - Exhaust ...
Clearance
- Clearance of the inlet valve stem ...
0.032 to 0.063 mm (0.00126 to 0.00248 inch)
Clearance
- Clearance of the exhaust valve stem ...
0.032 to 0.063 mm (0.00126 to 0.00248 inch)
(4) Length of valve
- Inlet valve and exhaust valve ...
119.775 to 120.125 mm (4.71554 to 4.72932 inch)
(5) Valve head
- Diameter of inlet valve head ...
32.3 to 32.5 mm (1.27165 to 1.27952 inch) - Diameter of exhaust valve head ...
32.3 to 32.5 mm (1.27165 to 1.27952 inch) - Diameter of exhaust valve head ...
Caterpillar Information System:
C3.4B Engines for Caterpillar Built Machines Lifter Group
TA2 Technical Inspection for 3512C Dynamic Gas Blending Marine Engines{0372, 1000, 753T, 7565} TA2 Technical Inspection for 3512C Dynamic Gas Blending Marine Engines{0372, 1000, 753T, 7565}
C3.4B Engines for Caterpillar Built Machines Piston and Rings
C3.4B Engines for Caterpillar Built Machines Connecting Rod
C3.4B Engines for Caterpillar Built Machines Main Bearing Journal
C4.4 Engines for Caterpillar Built Machines Electronic Control Module - Remove and Install
C3.4B Engines for Caterpillar Built Machines Connecting Rod Bearing Journal
C8.7 Marine Engine Engine Oil Level Gauge - Calibrate
C3.4B Engines for Caterpillar Built Machines Camshaft Bearings
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Top Mounted Exhaust Manifold
C4.4 Engines for Caterpillar Built Machines Refrigerant Compressor - Remove and Install
C4.4 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install - Engines with a Balancer Unit
C3.4B Engines for Caterpillar Built Machines Water Temperature Regulator and Housing
C8.7 Marine Engine Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
Instructions for Use of Cat® Coolant Conditioner for Modular Core Aluminum Radiators {1350, 1350, 1352, 1353, 1395} Instructions for Use of Cat® Coolant Conditioner for Modular Core Aluminum Radiators {1350, 1350, 1352, 1353, 1395}
C9 Generator Set Coolant (DEAC) - Change
C3.4B Engines for Caterpillar Built Machines Gear Group (Front)
2014/06/20 An Improved Inspection Process for Cylinder Liners Used in All 3500 Engines {1201, 1216}
2014/09/11 New Steering Line Assembly Is Now Available on Certain 621H, 623H, and 627H Wheel Tractor-Scrapers {4304, 5050}
G3306B Petroleum Generator Set Engines Engine Control Panel
G3306B Petroleum Generator Set Engines Fuel Pressure Is Low
G3306B Petroleum Generator Set Engines System Configuration Parameters
G3306B Petroleum Generator Set Engines Oxygen Level - Test
C175-16 PETROLEUM ENGINES High Pressure Fuel Rails - Remove and Install