Hood - Remove and Install - Clean Emissions Module
拆卸步骤
- 拆下螺栓 (2 ) 。 升起面板 (1) 。
Show/hide table
 | |
| 图 1 | g03617856 |
- 拆下开口销 (3) 、垫圈 (4) 和杆 (5) 。
Show/hide table
 | |
| 图 2 | g03639438 |
- 拆下螺栓 (4) 和发动机罩组件 (3) 。
Show/hide table
 | |
| 图 3 | g03639377 |
- 拆下螺栓 (8) 和盖 (9) 。
Show/hide table
 | |
| 图 4 | g03639519 |
- 拆下螺栓 (10) 和扶手组件 (11) 。 拆下螺栓 (12) 和薄片 (13) 。
Show/hide table
 | |
| 图 5 | g03639557 |
- 将适当的起吊设备安装到发动机罩组件 (15) 上。 发动机罩组件 (15) 的重量约为 41 kg (90 lb)。 拆下螺栓 (14) 和发动机罩组件 (15) 。
Show/hide table
 | |
| 图 6 | g03639676 |
- 切断所有电缆扎带，然后重新定位线束组件 (18) 。 拆卸螺栓 (16) 和 (19) 。 拆下支架 (17) 。
Show/hide table
 | |
| 图 7 | g03639605 |
安装步骤
- 按与拆卸相反的顺序安装清洁排放模块发动机罩。
Caterpillar Information System:
C4.4 Marine Generator Set Sea Water Pump Pressure Is Low
390F Excavator Machine Systems Control Valve (Boom Lowering)
UPS 750 Uninterruptible Power Supply System Operational Modes
G3600 A4 Engines Refill Capacities
374F Excavator Lifting and Tying Down the Machine
390F MHPU Mobile Hydraulic Power Unit Machine System Relief Valve (Main)
390F MHPU Mobile Hydraulic Power Unit Machine System Main Hydraulic Pump
G3600 A4 Engines Safety Messages
C27 and C32 Engines for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install
2014/05/30 New Rocker Arms Are Used for Certain C27 and C32 Machine Engines {1102, 1123}
C27 and C32 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor - Remove and Install
390F Excavator Radiator - Remove and Install - Rear
C4.4 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Fuel Temperature Sensor - Remove and Install
390F Excavator Engine Enclosure - Remove and Install
374F Excavator Air Cleaner Dust Valve - Clean/Inspect
C27 and C32 Engines for Caterpillar Built Machines Inlet Air Temperature Sensor - Remove and Install - Right Side and Left Side
2014/03/07 A New Jacket Water Elbow and Tube Assembly Are Used on Certain 3516C HD Marine Tier 3 Engines {1380}
C27 and C32 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
C4.4 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
C4.4 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
390F Excavator C18 Engine Supplement Engine Rear Mount - Remove and Install
C175-16 Petroleum Generator Set Engines Control Panel