Sea Water Pump Pressure Is Low
This procedure is only applicable to applications with a raw water cooling system.
The following code is associated with low sea water pump outlet pressure:
Show/hide table
Diagnostic Code for Low Sea Water Pump Pressure     | ||
---|---|---|
J1939 Code     | Code Description     | Comments     |
2435-17     | Seawater Pump Outlet Pressure : Low - least severe (1)     | Th ECM detects that the outlet pressure of the sea water pump is below the trip point for 30 seconds. The warning lamp is lit and the code is logged.     |
Probable Causes
- Diagnostic code
- Pump inlet blocked
- Pump impeller damaged
Recommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Show/hide table
Troubleshooting Test Steps     | Values     | Results     |
---|---|---|
1. Check for Diagnostic Codes A. Establish communication between the electronic service tool and the Electronic Control Module (ECM). Refer to Troubleshooting, "Electronic Service Tools", if necessary. B. Download the "Warranty Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes.     |
Diagnostic codes     |
Result: There are active or logged codes. Troubleshoot any codes before continuing with this procedure. Result: A 2435-17 code is active or recently logged. Proceed to Test Step 2.     |
2. Check the Inlet Pipe for the Sea Water Pump A. Disconnect the inlet pipe from the sea water pump. B. Check the inlet pipe for the following defects: · Blockages · Restrictions · Damage to the pipe · Loose connections     |
Inlet pipe     |
Result: The inlet pipe is blocked, restricted, damaged, or loose. Make all necessary repairs to the inlet pipe. Confirm that the fault has been eliminated. Result: The inlet pipe is OK. Do not reconnect the pipe. Proceed to Test Step 3.     |
3. Check the Sea Water Pump Impeller A. Crank the engine by hand and check the sea water pump impeller for damage.     |
Pump impeller     |
Result: The sea water pump impeller is damaged. Replace the impeller. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Disassemble" and Disassembly and Assembly, "Auxiliary Water Pump - Assemble". Confirm that the fault has been eliminated. Result: The sea water pump impeller is OK. Contact the Technical Communicator at a Cat dealer.     |
Caterpillar Information System:
390F Excavator Machine Systems Control Valve (Boom Lowering)
UPS 750 Uninterruptible Power Supply System Operational Modes
G3600 A4 Engines Refill Capacities
374F Excavator Lifting and Tying Down the Machine
390F MHPU Mobile Hydraulic Power Unit Machine System Relief Valve (Main)
390F MHPU Mobile Hydraulic Power Unit Machine System Main Hydraulic Pump
G3600 A4 Engines Safety Messages
C27 and C32 Engines for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install
2014/05/30 New Rocker Arms Are Used for Certain C27 and C32 Machine Engines {1102, 1123}
C27 and C32 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor - Remove and Install
390F Excavator Radiator - Remove and Install - Rear
349F and 352F Excavators Machine System Specifications Air Conditioner Lines
390F Excavator C18 Engine Supplement Hood - Remove and Install - Clean Emissions Module
C4.4 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Fuel Temperature Sensor - Remove and Install
390F Excavator Engine Enclosure - Remove and Install
374F Excavator Air Cleaner Dust Valve - Clean/Inspect
C27 and C32 Engines for Caterpillar Built Machines Inlet Air Temperature Sensor - Remove and Install - Right Side and Left Side
2014/03/07 A New Jacket Water Elbow and Tube Assembly Are Used on Certain 3516C HD Marine Tier 3 Engines {1380}
C27 and C32 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
C4.4 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
C4.4 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
390F Excavator C18 Engine Supplement Engine Rear Mount - Remove and Install