Engine Oil Pan
Show/hide table
 | |
| 图 1 | g03363050 |
发动机俯视图 | |
Show/hide table
 | |
| 图 2 | g03363057 |
发动机右视图 | |
Show/hide table
| 351-0316 油底壳总成 的技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 1 | 1 | 5P-5846 O 形密封圈 | 使用润滑剂稍微润滑即将密封的孔。 |
| 2 | 1 | 5P-8068 O 形密封圈 | 使用润滑剂稍微润滑即将密封的孔。 |
| 3 | 3 | 206-7331 排放塞 | 拧紧至扭矩为 70 ± 15 N·m (52 ± 11 lb ft)。 |
Show/hide table
 | |
| 图 3 | g03363461 |
拧紧顺序 | |
Show/hide table
 | |
| 图 4 | g03376138 |
再次拧紧顺序 | |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 | |
| 4 | 40 | 2P-3205 螺栓 | 装配发动机油底壳时，使用下述步骤： | |
| 油底壳的密封表面应没有机油、碎屑、垫片材料或任何其他密封胶。 | ||||
| 必须在涂抹密封胶后的 10 分钟内组装油底壳并将其拧紧至缸体上。 | ||||
| 1. 向下列位置涂抹 3 至 5 mm (0.1 至 0.2 in) 的超蓝 Loctite 587： 前壳体和缸体前部的连接点。 飞轮壳和缸体后部的连接点。 |
||||
| 2. 按照图 3 中所示的数字顺序，将螺栓 1 至螺栓 40 拧紧至扭矩为 40 ± 5 N·m (30 ± 4 lb ft)。 |
||||
| 3. 按照图 4 中所示的数字顺序，再次将螺栓 1 至螺栓 40 拧紧至扭矩为 47 ± 5 N·m (35 ± 4 lb ft)。 |
||||
Caterpillar Information System:
C4.4 and C7.1 Engines Data Link - Test
C13, C15, and C18 Tier 4 Final Engines Turbocharger
C15 and C18 Engines for Caterpillar Built Machines Exhaust Manifold
C13, C15, and C18 Tier 4 Final Engines Exhaust Manifold
2013/04/22 A New Exhaust Shield Group is Available for a G3516B Engine {1067}
C9.3 Engines for Caterpillar Built Machines Compression Brake - Assemble - Valve Assembly
C9.3 Engines for Caterpillar Built Machines Compression Brake - Disassemble - Valve Assembly
777F, 777G, and 785D OEM Off-Highway Truck/Tractors Water Delivery System Relief Valve (Cold Start) - Test
2013/03/29 An Improved Torque Sequence Is Used on Certain C18 Marine Engine Valve Covers {1107}
C32 Marine Generator Set Overhaul Considerations
C9.3 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Install
G3500H Generator Set Engine Speed/Timing - Test
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan
C9.3 Engines for Caterpillar Built Machines Rocker Arm - Disassemble
C9.3 Engines for Caterpillar Built Machines Rocker Arm - Assemble
C9.3 Engines for Caterpillar Built Machines Cylinder Head - Remove
C9.3 Engines for Caterpillar Built Machines Cylinder Head - Install
C9.3 Engines for Caterpillar Built Machines Lifter Group - Remove and Install
C9.3 Engines for Caterpillar Built Machines Camshaft Gear - Remove and Install
C7.1 Marine Engine Engine - Remove and Install
Installation of the Bolted Exhaust Shield for Certain G3500B Engines {1067} Installation of the Bolted Exhaust Shield for Certain G3500B Engines {1067}
C9.3 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
C9.3 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install