Rocker Shaft - Assemble
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Ensure that all components are clean and free from wear or damage. Refer to Specifications, "Rocker Shaft" for more information. If necessary, replace any components that are worn or damaged.
Show/hide table
Illustration 1 g01521630 - If necessary, install nuts (9) and adjusters (10) to rocker arm assemblies (3) and rocker arm assemblies (4). If the original adjusters are reused, ensure that the adjusters are installed in the original positions.
Show/hide table
Illustration 2 g01633015 - Install spring (7) to the front end of rocker shaft (5) and install retaining clip (8).
Show/hide table
Illustration 3 g01631213 - Lubricate the bores of rocker arm assemblies (3) and rocker arm assemblies (4) and rocker shaft (5) with clean engine oil.
- Install rocker arm assembly (3) for number 1 inlet valve to the rocker shaft. Install rocker arm assembly (4) for number 1 exhaust valve to rocker shaft (5).
Note: The rocker arm assembly for the inlet valve is longer than the rocker arm assembly for the exhaust valve. Used components should be installed in the original location.
- If necessary, ensure that locator (2) is correctly seated in pedestal (1). Ensure that the counterbores for the holes in rocker shaft (5) are upward. Align locator (2) with the hole to the front of rocker shaft (5). Install the pedestal to the rocker shaft.
Show/hide table
Improper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
- Install spring (6) to rocker shaft (5).
- Repeat Step 5 through Step7 to assemble the remaining components to rocker shaft (5).
- Install spring (7) to the rear end of rocker shaft (5) and install retaining clip (8).
End By:
- Install the rocker shaft assembly.
Caterpillar Information System:
C7.1 Marine Engine Rocker Shaft - Disassemble
374F Excavator Hydraulic System General Information (Main Pump System)
C3.3B Tier 4 Final Engines for Caterpillar Built Machines Cylinder Block
2013/03/27 New Fan Is Used For Main Stator Group Used On Certain Generator Set Engines {4457}
C4.4 Generator Sets Model View Illustrations
G3512 Generator Set Generator Lead Connections
C4.4 Generator Sets Additional Messages
G3500H 60Hz Generator Sets Parallel Operation
345-1236 Lifting Bracket{0599, 0629, 0632, 6605} 345-1236 Lifting Bracket{0599, 0629, 0632, 6605}
C3.3B Tier 4 Final Engines for Caterpillar Built Machines Engine Oil Pump
C4.4 and C7.1 Engines Oil Contains Fuel
C7.1 Marine Engine Expansion Tank - Remove and Install - Sea Water Cooled Engines
C7.1 Marine Engine Crankcase Breather - Remove and Install
2013/04/04 An Improved Coolant Hose Is Available for Certain C18 Marine Engines {1380, 3320}
C3.3B Tier 4 Final Engines for Caterpillar Built Machines Flywheel Housing
UPS 750 Uninterruptible Power Supply Telemetry Parameters
UPS 750 Uninterruptible Power Supply General Hazard Information
UPS 750 Uninterruptible Power Supply Safety Signs and Labels
UPS 750 Uninterruptible Power Supply Electrical System
UPS 750 Uninterruptible Power Supply Fire Prevention and Explosion Prevention
UPS 750 Uninterruptible Power Supply Troubleshooting
UPS 750 Uninterruptible Power Supply Additional Features
UPS 750 Uninterruptible Power Supply Reference Material
UPS 750 Uninterruptible Power Supply Acronyms