Exhaust Manifold
Show/hide table
Illustration 1 | g03320893 |
Show/hide table
Illustration 2 | g03320891 |
Tightening sequence |
Show/hide table
Specification for 354-6945 Exhaust Manifold Gp | |||
Item | Qty | Part | Specification Description |
1 | 8 | 012-7950 Plug | Before assembly, apply Loctite C5A copper anti-seize to the threads and bearing surface. |
2 | 16 | 168-7800 Locknut | Before assembly, apply Loctite C5A cooper anti-seize to the threads and bearing surface.
Tighten the locknuts in the numerical sequence as shown in the Illustration 2 to |
3 | 8 | 5K-5959 O-Ring Seal | Before assembly, lightly lubricate the bore. |
4 | 1 | 4N-5073 Elbow | The cup plug must be removed from each cylinder head before the elbows are connected. |
5 | 1 | 5F-4899 Bolt | Torque to |
6 | 5 | 9S-8752 Full Nut | Before assembly, apply Loctite C5A copper anti-seize to the threads and bearing surface. |
7 | 1 | 6V-2605 Taperlock Stud | Before assembly, apply blue Loctite 242 to the threads. |
8 | 4 | 7L-0520 Taperlock Stud | Torque to |
C | - | - | Distance between the top of the taperlock stud to cylinder head assembly is |
Caterpillar Information System:
CG137-08 and CG137-12 Generator Sets Exhaust Manifold - Water Cooled
CG137-08 and CG137-12 Generator Sets Air Cleaner Adapter
CG137-08 and CG137-12 Generator Sets Stub Shaft (Rear)
C32 Marine Engines Synchronization - Test
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 2813 - FMI 20
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 1962 - FMI 20
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 1961 - FMI 20
C175-16 Locomotive Engine Fuel Rail Temperature Is High
3516B Engine Exhaust Manifold - Remove and Install
C32 Marine Engines Sensor Signal (Analog, Active) - Test
Procedure for Installing Object Detection Software on Monitor Display Group {7347, 7490, 7620} Procedure for Installing Object Detection Software on Monitor Display Group {7347, 7490, 7620}
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Air Shutoff - Test
C32 Marine Engines Switch Circuits - Test
2012/11/09 Additional Crankcase Breathers Are Used on 3600 and C280 Engines {1317}
3516B Engine Engine Oil Cooler - Remove
C175-16 Locomotive Engine Starting - Test
3516B Engine Engine Oil Cooler - Install
C32 Marine Engines Sensor Signal (PWM) - Test
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Electrical Power Supply - Test
C32 Marine Engines Sensor Signal (Analog, Passive) - Test
421-9721 Top End Engine Overhaul Foundational Kit for 3412C Marine Engines{1000} 421-9721 Top End Engine Overhaul Foundational Kit for 3412C Marine Engines{1000}
2013/03/28 New Flywheel Assemblies Are Now Used on Certain Motor Graders and Excavators {1156}
Air/Fuel Controller (AFC) Module Software Update{1901} Air/Fuel Controller (AFC) Module Software Update{1901}
C175-16 Marine Engine Water Lines