Pump Drive - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-0520     | 冲头总成     | 1     |
E     | 4C-6141     | 轴承安装器     | 1     |
F     | 4C-9634     | 拉拔器螺柱     | 1     |
6V-3175 | 双作用油缸     | 1     | |
1P-1837 | 轴承拆卸工具适配器     | 1     | |
9U-6832 | 螺母     | 1     | |
G     | 8T-5096     | 千分表     | 1     |
Show/hide table
当您使用液压油缸和拉拔器螺柱时,务必确保拉拔器螺柱的额定容量达到或超过液压油缸的额定容量。 如果拉拔器螺柱未达到或超过液压油缸的额定容量,拉拔器螺柱可能突然发生故障。 拉拔器螺柱的突然故障可能导致人身伤亡。 |
- 将挡圈 (16) 、轴承 (13) 、垫片 (14) 和轴 (17) 安装到齿轮 (15) 中。 安装挡圈 (12) 。
Show/hide table
图 1 | g02911497 |
- 安装齿轮组件 (11) 。 安装螺栓 (10) 。
Show/hide table
图 2 | g02911384 |
Show/hide table
图 3 | g02911240 |
- 使用工具 (F) 安装轴承外圈 (9) 。
Show/hide table
图 4 | g02924277 |
- 使用工具 (E) 和适当的压具安装轴承 (8) 。 对另一侧重复此操作。
Show/hide table
图 5 | g02923357 |
- 使用工具 (A) 和适当的压具将轴承外圈 (7) 安装到法兰 (2) 中。
Show/hide table
图 6 | g02924022 |
- 安装齿轮组件 (5) 、垫片 (6) 和适配器 (2) 。
Show/hide table
图 7 | g02910317 |
Show/hide table
图 8 | g02925596 |
- 使用工具 (G) 测量齿轮组件 (5) 的端隙。 根据需要,使用垫片 (6) 以获得 0.10 mm (0.004 in) 至 0.20 mm (0.008in) 的端隙测量值。
- 安装螺栓 (3) 和板 (4) 。
Show/hide table
图 9 | g02894349 |
- 安装螺栓 (1) 和适配器 (2) 。
End By:
- 安装齿轮泵。
- 连接变速箱和变矩器。
Caterpillar Information System:
2012/03/05 A New Jacket Water Lines Group Is Used on C175-16 Generator Set Engines {1380}
2012/05/16 A New Valve Lifter Group and Dowel Are Used in C175-16 Engines {1209}
568 Forest Machines Machine Systems Track - Separate - PPR2
C175-16 Marine Propulsion Engines Coolant Temperature Control Module - Test
C175-16 Marine Propulsion Engines Turbocharger
C175-16 Marine Propulsion Engines Air Cleaner
C175-16 Locomotive Engine Flywheel Housing
C18 Generator Sets Engine Valve Lash - Check
C18 Generator Sets Engine Speed/Timing Sensor - Clean/Inspect
C175-16 Locomotive Engines Thermostatic Valve - Inspect
3512B and 3512C Petroleum Generator Set Engines ECM Software - Install
C175-16 Locomotive Engine Exhaust Has Excessive Black Smoke
C7 and C9 On-Highway Engines Engine Shutdown Occurs Intermittently
3500E Marine Engines Starting the Engine
3512C HD and 3516C HD Class I Division 2 Hazardous Location Generator Sets Manual Stop Procedure
3516C Industrial Engine Zinc Rods - Inspect/Replace
2012/03/15 New Guidelines For Cleaning Backup Alarms on Certain Cat Products {7406}
C175-16 Marine Propulsion Engines Gear Group (Front)
C175-16 Marine Propulsion Engines Gear Group (Front)
C175-16 and C175-20 Generator Set Engines Gear Group (Front)
2012/03/29 A Repair Option Is Available for Valve Cover Isolation Seals On Certain C9.3 Engines {1107, 7555}
C27 and C32 Generator Sets Additional Messages
C175-16 Marine Propulsion Engines Fuel Injection Pump
C175-16 Marine Propulsion Engines Exhaust Manifold