Rotating Rectifier - Inspect/Test
检查励磁电枢。 确认旋转整流器紧固。 如果怀疑整流器有故障,则转到本文中的 "测试旋转整流器。"信息部分。
Show/hide table
所需工具 | ||
零件号 | 零件名称 | 数量 |
237-5130 | 数字式万用表 | 1 |
257-9140 | 万用表 | 1 |
146-4080 | 数字万用表(RS-232) | 1 |
7X-1710 | 万用表表笔总成 | 1 |
Show/hide table
图 1 | g00555106 |
如果怀疑整流器出现故障,使用下述步骤进行测试。
- 拆下励磁机盖。
- 拆下将整流器固定到散热片上的螺母。
- 拆下二极管引线。
- 将整流器从散热片上提取下来。
- 请参阅插图 1。 将欧姆表引线跨接在整流器上。 记录欧姆表读数。
- 将欧姆表引线反接。 记录欧姆表读数。
当欧姆表引线以某一方向跨接在整流器上时,欧姆表应指示低电阻。 当欧姆表反向跨接时,欧姆表应指示高电阻。
如果欧姆表在正反两个方向都指示低电阻,说明整流器短路。 如果欧姆表在正反两个方向都指示高电阻,说明整流器开路。
使用具有用具有同等工作性能的整流器来更换有故障的整流器。 当订购整流器备件时应提供如下信息:
- 零件号
- 整流器型号
- 整流器类型
- 发电机的序列号
Show/hide table
图 2 | g00555113 |
测试灯 |
如果没有欧姆表,可以使用测试灯来测试整流器。 测试灯包括两个标准手电筒电池和一个手电筒灯泡。 请参阅插图 2。
如果怀疑整流器出现故障,使用下述步骤进行测试。
- 拆下励磁机盖。
- 拆下将整流器固定到散热片上的螺母。
- 拆下二极管引线。
- 将整流器从散热片上提取下来。
- 将测试灯跨接在整流器上。 注意灯泡是否点亮。
- 将测试灯反接在整流器上。 注意灯泡是否点亮。
当测试灯引线以某一方向跨接在整流器上时,灯泡应点亮。 当测试灯引线反向跨接时,灯泡不应点亮。
如果灯泡在正反两个方向都点亮,说明整流器短路。 如果灯泡在正反两个方向都不点亮,说明整流器短路。
使用具有用具有同等工作性能的整流器来更换有故障的整流器。 当订购整流器备件时应提供如下信息:
- 零件号
- 整流器型号
- 整流器类型
- 发电机的序列号
Caterpillar Information System:
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System Electronic Control Module (ECM) - Flash Program
C175-16 Generator Set Model View Illustrations
Extra O-ring Required for Water Pump Installation on Certain C15 On-Highway Truck Engines{1355, 1361, 1380, 1393} Extra O-ring Required for Water Pump Installation on Certain C15 On-Highway Truck Engines{1355, 1361, 1380, 1393}
3500C Marine Engines Engine Oil Pan
Utilizing the Electric Power SpecSizer for Proper Generator Set Sizing{1404, 7002} Utilizing the Electric Power SpecSizer for Proper Generator Set Sizing{1404, 7002}
2012/03/19 A New Exhaust Manifold Center Section and Turbocharger Mounting Hardware Are Used on Certain C18 Industrial Engines {1059}
3512B and 3512C Petroleum Generator Set Engines Coolant Temperature Is High
2012/02/15 New Heat Shield Groups Are Used on Certain C15 and C18 Generator Sets {1067}
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Coolant Contains Oil
C175-16 Marine Propulsion Engines Prelubrication - Test
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Coolant Contains Fuel
C175-16 Marine Engine Fuel Priming Pump
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System Electronic Control Module (ECM) - Configure
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System Electronic Control Module (ECM) - Replace
3512B and 3512C Petroleum Generator Set Engines Coolant Temperature Is Low
C175-16 Marine Engine Engine Oil Filter Housing
C175-16 Marine Engine Engine Oil and Water Pump Drive
Using the 164-2691 Printer Group {0374, 0599, 0684, 5057} Using the 164-2691 Printer Group {0374, 0599, 0684, 5057}
168-7720 Ultrasonic Wear Indicator III Group{0374, 0599, 0729, 0787} 168-7720 Ultrasonic Wear Indicator III Group{0374, 0599, 0729, 0787}
3500C Marine Engines Engine Oil Lines
C175-16 Marine Propulsion Engines Sensor Signal (Analog, Active) - Test
3512B and 3512C Petroleum Generator Set Engines Crankcase Pressure Is High
PMG3516 Power Module Product Description