Camshaft Bearings
Start By:
- Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 125-2739 | Bearing Pilot | 1 |
| 125-2740 | Backup Plate | 1 | |
| 125-2741 | Bearing Sleeve | 1 | |
| B | 6V-4013 | Screw | 1 |
| 6V-4010 | Puller Plate | 1 | |
| 8M-8778 | Taperlock Stud | 1 | |
| 2J-3506 | Full Nut | 1 | |
| 5P-8248 | Hard Washer | 1 | |
- Install the sleeve of Tooling (A) into camshaft bearing (1). Install the remainder of Tooling (A).
Show/hide table
Illustration 2 g01203308 - Install Tooling (B). Remove camshaft bearing (1).
Show/hide table
| |
| Illustration 1 | g01203149 |
|
205 | |
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 125-2739 | Bearing Pilot | 1 |
| 125-2740 | Backup Plate | 1 | |
| 125-2741 | Bearing Sleeve | 1 | |
| B | 6V-4013 | Screw | 1 |
| 6V-4010 | Puller Plate | 1 | |
| 8M-8778 | Taperlock Stud | 1 | |
| 2J-3506 | Full Nut | 1 | |
| 5P-8248 | Hard Washer | 1 | |
| C | 316-1493 | Hydraulic Puller | 1 |
| 350-7768 | Electric Hydraulic Pump Gp (115 V) | 1 | |
| 350-7769 | Electric Hydraulic Pump Gp (230 V) | 1 | |
- Install the sleeve of Tooling (A) into camshaft bearing (1). Install the remainder of Tooling (A).
Show/hide table
Illustration 4 g01203225 - Install Tooling (B) and Tooling (C). Remove camshaft bearing (1).
Show/hide table
|
| |
| Illustration 3 | g01203149 |
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 125-2739 | Bearing Pilot | 1 |
| 125-2740 | Backup Plate | 1 | |
| 125-2741 | Bearing Sleeve | 1 | |
| B | 6V-4013 | Screw | 1 |
| 6V-4010 | Puller Plate | 1 | |
| 8M-8778 | Taperlock Stud | 1 | |
| 2J-3506 | Full Nut | 1 | |
| 5P-8248 | Hard Washer | 1 | |
- Install camshaft bearing (1) onto Tooling (A).
Show/hide table
Illustration 6 g01203523 Show/hide table
Illustration 7 g01204034 Note: The camshaft bearing joint must be in the 2 O'clock or the 10 O'clock position. The oil hole must be located on the centerline of the bore.
- Position Tooling (A) and camshaft bearing (1) into the bearing bore. Make sure that the groove in the back of camshaft bearing (1) is aligned with oil hole (2) in the cylinder block. Install Tooling (B). Install camshaft bearing (1).
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| |
| Illustration 5 | g01203522 |
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 125-2739 | Bearing Pilot | 1 |
| 125-2740 | Backup Plate | 1 | |
| 125-2741 | Bearing Sleeve | 1 | |
| B | 6V-4013 | Screw | 1 |
| 6V-4010 | Puller Plate | 1 | |
| 8M-8778 | Taperlock Stud | 1 | |
| 2J-3506 | Full Nut | 1 | |
| 5P-8248 | Hard Washer | 1 | |
| C | 316-1493 | Hydraulic Puller | 1 |
| 350-7768 | Electric Hydraulic Pump Gp (115 V) | 1 | |
| 350-7769 | Electric Hydraulic Pump Gp (230 V) | 1 | |
| 8S-8292 | Extension | 1 | |
- Install camshaft bearing (1) onto Tooling (A).
Show/hide table
Illustration 9 g01203527 Show/hide table
Illustration 10 g01204034 Note: The camshaft bearing joint must be in the 2 O'clock or the 10 O'clock position. The oil hole must be located on the centerline of the bore.
- Position Tooling (A) and camshaft bearing (1) into the bearing bore. Make sure that the groove in the back of camshaft bearing (1) is aligned with oil hole (2) in the cylinder block. Install Tooling (B) and Tooling (C). Install camshaft bearing (1).
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
|
| |
| Illustration 8 | g01203522 |
End By:
- Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Caterpillar Information System:
C175-16 Marine Engine Camshaft
2015/08/07 Tab Must Be Removed on Certain Turbochargers That Are Equipped on Certain C7 and C9 On-Highway Truck Engines {1052, 1053}
2012/02/27 An Alternate Repair Option Is Used for the Cat 270 Air Compressor {1803}
2012/02/07 New Improved Hybrid Fuel lines Are Now Used on Certain C11 and C13 Industrial Engines {1274}
C175-16 Marine Engine Valve Lifter
C175-16 Marine Engines Zinc Rods - Inspect/Replace
C175-16 Marine Engine Cylinder Head
C175-16 Marine Engine Rocker Shaft
C175-16 Marine Engine Rocker Shaft and Push Rods
C175-16 Marine Engine Crankcase Breather
1U-8846 Gasket Sealant Has Been Removed From 3N-5904 Gear Seal Kit {1000, 7000} 1U-8846 Gasket Sealant Has Been Removed From 3N-5904 Gear Seal Kit {1000, 7000}
3516C Industrial Engine Model View Illustrations
C175-16 Marine Engine Piston Cooling Jets
3500B High Displacement Locomotive Engines Connecting Rod
3500C Marine Engines Product Lifting
2012/02/08 A New NOx Reduction System (NRS) Venturi Is Used on Certain C9.3 Industrial Engines {1071}
3508C, 3512C and 3516C Locomotive Engines Thermostatic Valve
2012/02/10 A New Band Clamp Is Available for Turbochargers on Certain 3500 and C175-16 Engines {1052, 1053}
Installation Procedure for Product Link PL421 Retrofit{7606} Installation Procedure for Product Link PL421 Retrofit{7606}
G3600 Engines Fuel Control - Low BTU
2012/02/10 A New Oil Emulsion Preventative Is Now Used on the Brake Actuators of Certain Heavy Duty C15 and C18 Engines {1130}
2012/02/08 New Software Is Now Used to Improve Engine Speed Stability on Certain C7 Industrial Snow Blower Engines {1901, 1920}
Using 149-0174 Non-Choker Style Fabric Baskets to Install or Remove Bucket or Blade Cutting Edges{0374, 0599, 0632, 0700, 0751, 6800} Using 149-0174 Non-Choker Style Fabric Baskets to Install or Remove Bucket or Blade Cutting Edges{0374, 0599, 0632, 0700, 0751, 6800}
Operating Instructions for 155-1536 Valve Recession Tool Kit for all G3500 and 3500 Engines{0374, 0599, 0701, 0703, 0759, 0767} Operating Instructions for 155-1536 Valve Recession Tool Kit for all G3500 and 3500 Engines{0374, 0599, 0701, 0703, 0759, 0767}