Cylinder Head Valves
Show/hide table
图 1 | g02829216 |
Show/hide table
技术规格 - 338-8671 缸盖总成、 338-8672 缸盖总成和 317-2440 缸盖总成 | |||
项目 | 数量 | 零件 | 技术规格说明 |
1 | 4 | 316-5976 弹簧 | 测试力下的长度为 测试力为 测试后的自由长度为 |
2 | 4 | 316-5977 弹簧 | 测试力下的长度为 测试力为 测试后的自由长度为 |
3 | 2 | 316-5980 气门杆密封件 | 将阀杆密封件安装到进气阀上。
组装前涂抹发动机机油。 |
4 | 2 | 316-5981 垫圈 | 将垫圈安装到排气阀上。 |
A | - | - | 从缸盖顶部到气门导管顶部的高度为 |
5 | 2 | 197-6995 气门导管 | 安装后排气门导管的孔径为 |
6 | 2 | 133-9306 气门导管 | 安装后进气门导管的孔径为 |
7 | 2 | 443-2712 排气门 | 组装前,用清洁的发动机机油涂覆排气阀杆。
气门杆直径 (B) 为 气门直径 (D) 为 端面角度为 44.40 ± 0.25 度。 |
8 | 2 | 210-2542 进气阀 | 组装前,用清洁的发动机机油涂覆进气阀杆。
气门杆直径 (C) 为 气门直径 (E) 为 端面角度为 19.40 ± 0.25 度。 |
9 | 2 | 130-2608 气门座镶圈 | 排气门座镶圈的直径为 缸盖的缸径为 端面角度为 45.00 ± 0.25 度。 |
10 | 2 | 130-2607 气门座镶圈 | 进气门座镶圈的直径为 缸盖的缸径为 端面角度为 20.00 ± 0.25 度。 |
Caterpillar Information System:
3512C and 3516C Industrial Engines Air Lines
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Site Preparation
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Receiving and Handling
Instructions for Use of Cat Coolant Conditioner for Aluminum Components {1350, 1352, 1395} Instructions for Use of Cat Coolant Conditioner for Aluminum Components {1350, 1352, 1395}
349F and 352F Excavators Radio - If Equipped
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Symbols
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Acronyms
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Serial Number Plate
3516B Generator Set Engines with Dynamic Gas Blending General Information
C15 and C18 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Remove and Install
Product Identification Numbers (PIN) Location Guide Excavator (Mini)
3500B and 3500C Marine Engines Cylinder Head Valves
3512C and 3516C Marine Engines Crankshaft
3508C, 3512C and 3516C Locomotive Engines Turbocharger Oil Lines
2012/01/19 Sealing of the Ignition Harness on Certain G3300 and G3400 Engines {1408, 7555}
Product Identification Numbers (PIN) Location Guide Material Handler (Track)
C13 Engine for Combat and Tactical Vehicles Electronic Control Wiring Group
Product Identification Numbers (PIN) Location Guide Material Handler (Wheel)
C13 Engine for Combat and Tactical Vehicles Compression Brake
3516C Locomotive Engines Selective Catalytic Reduction Dosing Lines Blockage - Test
2012/01/16 A New Piston and Rod Group with a One-Piece Piston Is Used in Certain 3512B and 3516B High-Displacement Locomotive Engines {1225}
C15 and C18 Engines for Caterpillar Built Machines Fumes Disposal Filter - Remove and Install
Product Identification Numbers (PIN) Location Guide Backhoe Loader