CG137-08 and CG137-12 Generator Sets Caterpillar

Cylinder Head

Usage:

Show/hide table




Illustration 1	g02712379

Show/hide table




Illustration 2	g02712380

Show/hide table

Table 1
Specification for 351-1922 Cylinder Head Gp
Item	Qty	Part	Specification Description
Use any one of the following tightening procedure to tighten the bolts for the cylinder head:
Tighten bolt (27) through bolt (39) only after bolt (1) through bolt (26) have been given the final torque.
1	40	236-0484 Bolt	Use the following procedure in order to tighten the bolts for the cylinder head: 1. Before assembly, apply clean engine oil to the threads of the bolts. 2. Tighten bolt 1 through bolt 20 in the numerical sequence as shown in Illustration 2 to 270 ± 27 N·m (200 ± 20 lb ft). 3.Again, tighten bolt 1 through bolt 20 in the numerical sequence as shown in Illustration 2 to 450 ± 20 N·m (332 ± 15 lb ft). 4. Again, retighten bolt 1 through bolt 20 in the numerical sequence as shown in Illustration 2 to 450 ± 20 N·m (332 ± 15 lb ft). 5. Install the rocker arm group. 6. Tighten bolt 21 through bolt 26 in the numerical sequence as shown in Illustration 2 to 270 ± 27 N·m (200 ± 20 lb ft). 7. Again, tighten bolt 21 through bolt 26 in the numerical sequence as shown in Illustration 2 to 450 ± 20 N·m (332 ± 15 lb ft) 8. Again, retighten bolt 21 through bolt 26 in the numerical sequence as shown in Illustration 2 to 450 ± 20 N·m (332 ± 15 lb ft). 9. Tighten bolt 27 through bolt 39 in the numerical sequence as shown in Illustration 2 to 43 ± 7 N·m (32 ± 5 lb ft).
1	12	234-9558 Bolt
2	26	0L-1352 Bolt
Alternate tightening procedure to tighten the bolts for the cylinder head:
-	-	-	Use the following procedure in order to tighten the bolts for the cylinder head: 1. Before assembly, apply molybdenum paste to the threads of the (3/4) bolts. 2. Tighten bolt 1 through bolt 20 in the numerical sequence as shown in Illustration 2 to 270 ± 27 N·m (200 ± 20 lb ft). 3.Again, tighten bolt 1 through bolt 20 in the numerical sequence as shown in Illustration 2 to 390 ± 10 N·m (288 ± 7 lb ft). 4. Again, retighten bolt 1 through bolt 20 in the numerical sequence as shown in Illustration 2 to 390 ± 10 N·m (288 ± 7 lb ft). 5. Install the rocker arm group. 6. Tighten bolt 21 through bolt 26 in the numerical sequence as shown in Illustration 2 to 270 ± 27 N·m (200 ± 20 lb ft). 7. Again, tighten bolt 21 through bolt 26 in the numerical sequence as shown in Illustration 2 to 390 ± 10 N·m (288 ± 7 lb ft) 8. Again, retighten bolt 21 through bolt 26 in the numerical sequence as shown in Illustration 2 to 390 ± 10 N·m (288 ± 7 lb ft). Before assembly, lubricate the threads of the (3/8) bolts with clean engine oil. 9. Tighten bolt 27 through bolt 39 in the numerical sequence as shown in Illustration 2 to 43 ± 7 N·m (32 ± 5 lb ft).
3	2	4N-0932 Cup Plug	Apply, Loctite 11358 sealant to the bores of the cup plugs. Installation depth is 1.25 ± 0.25 mm (0.049 ± 0.010 inch).
4	2	5P-0063 Cup Plug	Apply, Loctite 11358 sealant to the bores of the cup plugs. Installation depth is 1.25 ± 0.25 mm (0.049 ± 0.010 inch).

Show/hide table




Illustration 3	g02712382

Show/hide table

Table 2
Specification for 351-1922 Cylinder Head Gp
Item	Qty	Part	Specification Description
5	6	109-0073 O-Ring Seal	Before assembly, lubricate the bore of the O-ring with silicon compound.
6	6	213-7539 Adapter	Before assembly, apply antiseize to the threads. Torque to 95 ± 7 N·m (70 ± 5 lb ft).
Apply high strength, high temperature anaerobic flange sealant to all the bores of the cup plugs.
7	5	3B-0645 Cup Plug	Installation depth is 2.0 ± 0.5 mm (0.08 ± 0.02 inch).
8	5	3B-0645 Cup Plug	Installation depth is 4.5 ± 0.5 mm (0.18 ± 0.02 inch).
9	12	3B-0623 Cup Plug	Installation depth is 0.8 ± 0.5 mm (0.03 ± 0.02 inch).

Caterpillar Information System:

3500C Marine Engines Refill Capacities

2011/09/20 Updated Engine Diagnostic Publications for Certain C7 and C9 ACERT Powered Machines Is Available {1000, 1250, 1450}

CG137-08 and CG137-12 Engines Air Starting Motor - Remove and Install - Alternate Air Starting Motor - TDI

CG137-08 and CG137-12 Engines Air Starting Motor - Remove and Install

CG137-08 and CG137-12 Generator Sets Camshaft

C15 Engines for Combat and Tactical Vehicles Cooling System

NEHS1120: Truck Body Lifting Pins {0599, 0629, 0632, 0757, 1122, 7006, 7006, 7258} NEHS1120: Truck Body Lifting Pins {0599, 0629, 0632, 0757, 1122, 7006, 7006, 7258}

C1.7, C1.8, and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Engine Crankcase Pressure (Blowby) - Test

C2.6 and C3.3B Tier 2 and EU Stage 2 Engines for Caterpillar Built Machines Engine Speed - Check

C15 Engines for Combat and Tactical Vehicles Cooling System - Check - Overheating

2011/10/19 A New Product Link Registration/Activation Process Now Available For Product Link (PL) 522 and 523 {7606}

CG137-08 and CG137-12 Generator Sets Ignition Transformer

CG137-08 and CG137-12 Generator Sets Cylinder Head Valves

CG137-08 and CG137-12 Generator Sets Exhaust Bypass Valve

2011/11/10 Spacers have been Added to the Shaft Shoulder of the Console Support on Certain Cat Excavators {7324}

G3500 Valve Runout Tool{0760, 1100, 1101, 1103, 1104, 1105} G3500 Valve Runout Tool{0760, 1100, 1101, 1103, 1104, 1105}

2011/09/28 New Rocker Arm Assemblies Are Available for Certain C15 Truck Engines {1102, 1123}

G3512 EPA Emergency and Non-Emergency Standby Generator Sets Generator Lead Connections

3512, 3508 and 3516 Generator Sets Refill Capacities

3500 Generator Sets Coolant (DEAC) - Change

3500 Generator Sets Coolant (ELC) - Change

349F and 352F Excavators Hydraulic System Automatic Travel Speed Control - Test

3500 Generator Sets Coolant Level - Check

TH55-E70 and TH55-E90 Petroleum Transmissions Transmission Planetary - Disassemble