Cylinder Block
Show/hide table
图 1 | g03497822 |
发动机前视图 |
Show/hide table
技术规格 - 370-9890 缸体总成 | |||
项目 | 数量 | 零件 | 技术规格说明 |
- | 组装时,目视板底部、缸体顶部和密封垫板两侧均不应有燃油、机油、水和密封垫粘合剂、组装固定胶或任何其他异物。 | ||
1 | 2 | 4W-4813 塞 | 拧紧至扭矩为 |
2 | 4 | 5F-9657 O 形密封圈 | 使用润滑剂稍微润滑即将密封的孔。 |
3 | 18 | 101-1198 凸轮轴轴承 | 在缸体每侧,穿过凸轮轴轴承油孔和凸轮轴轴承接合面的所有中线位置必须如图 1 所示。 |
油孔位置与水平面之间的夹角 (D) 必须为 20 ± 5 度,如 1 图所示。 | |||
缸体内凸轮轴轴承的孔径为 |
|||
4 | 3 | 7X-4805 O 形密封圈 | 使用润滑剂稍微润滑即将密封的孔。 |
5 | 8 | 6V-3348 O 形密封圈 | 使用润滑剂稍微润滑即将密封的孔。 |
A | 32 | 8T-0099 定位销 | 定位销自缸体上表面的延伸长度为 |
C | 16 | 197-7008 定位销 | 定位销自缸体上表面的延伸长度为 |
E | 9 | 223-1696 曲轴轴承盖 | 曲轴轴承盖的宽度为 主轴承盖的缸体宽度为 |
F | - | - | 从曲轴轴承孔中心线至缸体顶部的新尺寸为 |
G | - | - | 从曲轴轴承孔中心线到缸体底部(油底壳轨)的新尺寸为 |
H | - | - | 缸体中的主轴承孔径为 |
Show/hide table
图 2 | g03497823 |
剖面 B-B |
Show/hide table
技术规格 - 370-9890 缸体总成 | |||
项目 | 数量 | 零件 | 技术规格说明 |
6 | 1 | 214-7568 O 形密封圈 | 使用润滑剂稍微润滑即将密封的孔。 |
J | 2 | 7N-2047 定位销 | 定位销自缸体后表面的延伸长度为 |
K | 1 | 7N-2047 定位销 | 定位销自缸体前表面的延伸长度为 |
L | 2 | 4N-0683 定位销 | 定位销自缸体后表面的延伸长度为 |
M | 2 | 7N-2044 定位销 | 定位销自缸体前表面的延伸长度为 |
Show/hide table
图 3 | g03497824 |
前视图 |
Show/hide table
项目 | 数量 | 零件 | 技术规格说明 |
7 | 16 | 352-6061 缸套密封件 | 将干燥的密封件组装到清洁干燥的缸套槽上。
组装前,用 P-80 橡胶润滑剂乳化液或液体肥皂涂覆密封件。 |
8 | 48 | 7N-2046 O 形密封圈 | 组装前,用 P-80 橡胶润滑剂乳化液或液体肥皂涂覆密封件。 |
9 | 36 | 7X-7925 螺栓 | 按照以下步骤拧紧曲轴轴承盖螺栓:
1. 组装前,用清洁的发动机机油完全润滑螺纹。 2. 用手将螺栓拧紧到螺纹孔中。 3. 按照图 3 中所示的数字顺序拧紧螺栓至 4. 再将螺栓拧紧 180 ± 5 度。 |
Caterpillar Information System:
TA19 M4WD Agricultural Transmission Pump Drive
TA19 M4WD Agricultural Transmission Transmission Hydraulic Control
C27 Generator Set Parallel Operation
2011/07/28 New Fuel Pressure Regulators Are Now Used on 3126 and C7 On-Highway Engines {1715}
C27 Generator Set Before Starting Engine
3516C Generator Set Engines Injector Solenoid - Test
992K Wheel Loader Hoses and Clamps - Inspect/Replace
3516C Generator Set Engines Speed/Timing - Test
C3.3B and C3.8 Engines for Caterpillar Built Machines General Information
C3.4B Industrial Engine Cold Weather Operation
C27 Generator Set Starting the Engine
C7.1 (Mech) Industrial Engine Cleanliness of Fuel System Components
120 Motor Graders Bypass Switch (Power Train Oil Filter)
C3.4B Industrial Engine Engine Starting
C3.4B Engines For Caterpillar Built Machines Engine Oil Filter Base
C3.4B Engines For Caterpillar Built Machines Connecting Rod
3516C Generator Sets Product Storage
C3.4B Engines For Caterpillar Built Machines Gear Group (Front)
Use of the 352-6061 Liner Seal and the 8N-4707 Filler Band {1201, 1201, 7555} Use of the 352-6061 Liner Seal and the 8N-4707 Filler Band {1201, 1201, 7555}
2011/07/29 An Improved Procedure Is Now Used to Determine the Reason for a Reoccurring Engine Timing Offset Code on Certain C27 and C32 Engines {1000}
370-8083 Plate Assembly - Lifting{0700, 0701, 0703, 1000, 1100} 370-8083 Plate Assembly - Lifting{0700, 0701, 0703, 1000, 1100}
3516C Generator Set Engines Electrical Power Supply - Test
320E and 323E Excavators Quick Coupler Operation - Circuit for Universal Coupler (If Equipped)
2011/08/04 New Valve Train Components for C175 Generator Set Engines {1102, 1121, 1123, 1209}